A spring-mass-damper system has transfer function as follow: TF = (35²+45+k) Spring constant is found to be k= 4.9 If step input H= 9.2 is applied to this system, find out the expression of system response, and fill the following blank with the state-state response of this system under the given step input. (please keep two digits after decimal point) ***Please include all calculation steps in the uploaded file.

A spring-mass-damper system has transfer function as follow: TF = (35²+45+k) Spring constant is found to be k= 4.9 If step input H= 9.2 is applied to this system, find out the expression of system response, and fill the following blank with the state-state response of this system under the given step input. (please keep two digits after decimal point) ***Please include all calculation steps in the uploaded file.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the effect of increasing and decreasing proportional gain to the system output. Discuss the effect of increasing and decreasing derivative gain to the system output. Discuss the effect of increasing and decreasing the integral gain to the system output. 4. Discuss some advantages of using Simulink over the MATLAB codes I WANT THE ANSWER FOR THIS QUESTION WITHOUT PLAGIARISM
If the following data-input waveforms applied to the comparator. the * output in relation to the inputs will be Ag COMP A = BE Bo B. B1 ......
In Figure is given .. 10 - Ys) Ys) R() G{s) O A) there are not correct ans swers O B) multiple input and single output system (MISO) C) single input and multiple output system (SIMO) O D) single input and single output system (SISO) E) multiple input and multiple output system (MIMO)
Q5. Design a counter which counts down, with the repeated sequence: (2, 1, 0, 2, 1, 0, ...) when the input to the counter circuit is 1. The counter doesn't count (stays at the same state) when the input is 0. The circuit is to be designed by treating the unused states as don't care conditions. Fill out the state transition table, and draw a state diagram and your schematic for the design. Use positive edge D flip flops in your design.
5
Analogue 2
Fast please
In a stair step A/D converter, clock frequency is 1 MHz, threshold voltage is (0.1 V). The full scale output of D/A converter is (10.23 V). If it is a 10 bit device. Find the conversion time for an analog input of (3.728 V)? 373 UG
HW 1)find the oufputof the Sxstena hcn)=2ucn-1) iR its input xcn) =()"u() %3D
6. Consider the circuit depieted in the figure below, R V,eiut where we shall assume that the input voltage can be written as Vin(t) = Re{Voet} with complex-valued Vg, and likewise that the output voltage Vout(t) = Re{Vje*} with complex-valued Vị. With j = V-1, the complex impedances of resistors, ca- pacitors, and inductors in this case are respectively given by ZR = R, Zc = ZL = jwL. (a) Determine Vı/Vo as a function the angular frequency w given the parameters R and C. (b) Evaluate Vi/Vo in the limit w +0 and in the limit w + o0. Is the circuit above a low-pass filter, a high-pass filter, or something else? w
a) Using a NTC thermistor with "B=4000K, resistance: 5k2 at 25°C" we want to measure the temperature of an environment in the range 50°C - 100°C. Design a suitable circuit for this purpose with "zero" output signal |v) value at 25ºC. Express the output and its temperature-sensitivity in terms of temperature (y=f(T°C) and dy/dT= f(TºC)). Roughly draw y and dy/dT for the given temperature range. (Note: For NTC: RNTC=Roexp(B(1/T-1/To))
Circuit design: Find an open-collector output comparator IC and use it to implement a sensor circuit, Such that- The comparator turns on a LED if the input signal voltage is greater than 3.9.You can feed the input signal voltage using a potentiometer.LED should turn on if signal voltage >3.9V And turn off otherwise. N:S: If you can construct the circuit please give an short explanation