A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.4 kN. When the force is increased from 2.4 kN to 9 kN, the specimen elongates 0.250 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.

A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.4 kN. When the force is increased from 2.4 kN to 9 kN, the specimen elongates 0.250 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

A specimen is originally lft long, has a diameter of 0.5in, and is subjected to a force of 5001b. When the force is increased from 5001b to 1,8001b, the specimen elongates 0.009in. Determine the modulus of elasticity (2 decimal places in 103 ksi) for the material if it remains linear elastic.
Q2: A specimen is originally 1 ft long, has a diameter of 0.5 in., and is subjected to a force of 500lb. When the force is increased from 500lb to 1800lb, the specimen elongates 0.009in. Determine the modulus of elasticity (E) for the material if it remains elastic.
A cylindrical specimen of stainless steel having a diameter of 12.8 mm (0.505 in.) and a gauge length of 50.800 mm (2.000 in.) is pulled in tension. Use the load–elongation characteristics shown in the following table to answer the following: a. Plot the data as engineering stress versus engineering strain. b. Compute the modulus of elasticity. 66 c. Determine the yield strength at a strain offset of 0.002. d. Determine the tensile strength of this alloy. e. What is the approximate ductility, in percent elongation? f. Compute the modulus of resilience
Question 2:A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a forceof 2.5 kN. When the force is increased from 2.5 kN to 9 kN, the specimen elongates 0.225mm. Determine the modulus of elasticity for the material if it remains linear elastic.
The rectangular block shown in Figure is subjected to tension within the elastic range. The increase in the length of a is 2 * 10-3in. and the contraction of b is 3.25 * 10-4 in. If the original lengths of a and b were 2 in. and 1 in., respectively, what is Poisson’s ratio for the material of the specimen?
A specimen is originally 300mm long, has a diameter of 14mm, and is subjected to a force of 2 kN. When the force is increased from 2 kN to 8 kN, the specimen elongates 0.225 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.
A rectangular block of aluminum 30 mm * 60 mm * 90 mm is placed in a pressure chamber and subjected to a pressure of 100 MPa. If the modulus of elasticity is 70 GPa and Poisson’s ratio is 0.333, what will be the decrease in the longest side of the block, assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the block?
A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the length increases to 150.40mm. The material remains within the linear elastic region and its modulus of elasticity is 200,000 MPa. Determine the force, in Newton (N), applied to the test.
A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN. When the force is increased from 4kN to 7.5kN the specimen elongates 0.225mm. Determine the modulus of elasticity for the material if it remains linear elastic.
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. Determine the lateral strain. * Your answer Determine the axial strain. Your answer Determine the Poisson's ratio v. * Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
A round steel alloy bar with a diameter of 19 mm and a gauge length of 76 mm was subjected to tension, with the results shown in Table P3.26. Using a computer spreadsheet program, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel alloy and the deformation corresponding to a 37 kN load. TABLE P3.26 Deformation, Load, kN mm 9 0.0286 18 0.0572 27 0.0859 36 0.1145 45 0.1431 54 0.1718