A solid steel shaft 5 m long is stressed at 80 MPa when twisted through 4°. Using G = 83 GPa, compute the shaft diameter and torsional stiffness. What power can be transmitted by the shaft at 20 Hz? Answers: 138 mm, 591.2 kN.m/rad and 5.19 MW

A solid steel shaft 5 m long is stressed at 80 MPa when twisted through 4°. Using G = 83 GPa, compute the shaft diameter and torsional stiffness. What power can be transmitted by the shaft at 20 Hz? Answers: 138 mm, 591.2 kN.m/rad and 5.19 MW

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: A pump receives 60 Liters per second of water with specific volume of 0.00112 m³/kg at a head of 750...

A: Correct answer: 606.39 kW

Q: The pressure P exerted by a flowing fluid on a stationary body depends upon the length l of the body...

A: F=fL,V,ρ,μ,gϕF,L,V,ρ,μ,g=0 Quantity DimensionF MLT-2L ...

Q: A1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Air at 25°C flows...

Q: A cenrifugal pump having outer diameter equal two times the inner diameter and running at 1200rpm wo...

Q: The suction diameter of 60 mm reads 2 psi vacuum and 50 mm diameter discharge with 250 kpag. The suc...

Q: 1. A ball A is thrown vertically upward from the top of a 30-m high building with an initial velocit...

Q: Steam at 10 MPa and 550 °C enters reheat-regenerative engine and expands to 3 MPa where m, is extrac...

A: Given DataP1=10MPaT1=550°CP2=3MPaP4=1.8MPaT=45°C ***As per our company policy we are supposed to do ...

Q: To use the conservation of energy with nonconservative forces to determine the maximum height and ve...

Q: A hydro electric installation is to develop 12 200 Hp. The head is 8ft and the speed of rotation is ...

A: GIVEN DATA- POWER =12200hp HEAD H=8ft N=150 rpm Ns=485 WE HAVE TO FIND NO. OF TURBINE

Q: 6. A 130 cc block has a piece of lead tied to it. Suppose that the SG of lead is 11.13 and SG of the...

A: Given data Volume of block = 130 cm3 = 0.00013 m3Specific gravity of block = 0.25 Specific gravity o...

Q: 8. As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is req...

A: GIVEN DATA- A HYDRAULIC PRESS GIVEN WE HAVE TO FIND FORCE F

Q: A vehicle and trailer combination cross a 12-meter bridge with axle loads of 10, 20, and 30 kN separ...

Q: The power generated by an adiabatic steam turbine is 5MW, when the steam enters the turbine at a pre...

Q: A force, F = 12 N, making an angle of 02 = 15° to the ramp pulls up a block of mass m = 2 kg. The ra...

Q: -why should the supply frequency be maintained constamt

Q: if Re 77 Soo %3D 등 = \ , * 103 Determine f %3D from mod'] chart.

Q: 5.5 An automobile has a characteristic length and area of 8 ft and 60 ft²', respectively. When teste...

A: Answer: The properties of air at sea level are: P = 0.00238 slug/ft3μ =3.72x10-7 slug/ft.s The Reyno...

Q: Inside a 145 mm x 334 mm rectangular duct, air at 26 N/s, 24 deg C, and 108 kPa flows. Solve for the...

Q: A vertical rod of length L and diameter dis fixed at its upper end and carries a load Wat its lower ...

A: GIVEN DATA- A ROD FIXED AT TOP AND SUBJECTED TO TORQUE AND LOAD W WE HAVE TO FIND EXPRESSION FOR POI...

Q: 13. What are the major functions of drill string in drilling engineering?

A: Since we only solve one question, we will answer the first. Please resubmit the other questions you ...

Q: A container shown is at 90 deg F, The pressure at point A was measured at 41 in of Hg. Find the pre...

Q: Some ECOR1048 students are curious about expanding their knowledgebase and conduct an experiment. Th...

Q: The laguna lake has a deepness floor measured at 0.06 kms. Determine the absolute pressure in kPa ha...

A: Hydrostatic pressure P = Patm + density*gravity*h

Q: 2. The horizontal rigid bar AB is hinged (pinned) to a vertical wall at A and supported by two steel...

Q: As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is requir...

A: GIVEN DATA- A HYDRAULIC PRESS GIVEN WE HAVE TO FIND FORCE F

Q: One mole of an ideal gas, originally at a volume 8.21 liters at 1,000 K, is allowed to expand adiaba...

Q: Please help me derive the C.O.P of the refrigerator as a function of temperature using the temperatu...

Q: The left limb of a U-tube manometer is connected to a pipe conveying water, the level of mercury (SG...

A: P = Po + ρgh

Q: 8 kg/s of R134a is condensed from 700 KPa and 70 °C to saturated liquid at 700 KPa in a water- coole...

A: Given Data Mass flow rate of refrigerant=8 kg/s State 1: 700 kPa,70°C State 2: saturated liquid,700...

Q: A U-tube is made up of two capillaries with bores of 0.0039 ft and 0.0078 ft. A liquid with a surfac...

A: Answer: The density of the liquid is 943.2875 kg/m3.

Q: Kerosene, SG=0.82 Air, SG=0.0012 Benzene, SG= 0.88 100mm B 200mm 150mm 90mm Water Hg 400mm

A: Given Data: The specific gravity of mercury, SG=13.6

Q: "he rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Fin...

Q: Solve for the inverse of the given matrix by definition A*A-1 = A-1*A = | 1 7 -5 |A| = |-2 -3 4 8 9.

Q: Oil is to flow through a pipe at 80°C, and for experimental purposes, the oil flow must be hydrodyna...

Q: 1. Consider this flow and level control system below. The tank is cylindrical and has a radius of 0....

A: Given: Flow rate of the water→Q=π400 m3min=π24000 m3sec Radius of the tank→r=0.5 m Hence cross secti...

Q: A vertical rod of length L and diameter dis fixed at its upper end and carries a load Wat its lower ...

A: Write the torsion equation for the rod. TJ=GθL Here, J is the polar moment of inertia, and G is the ...

Q: 2. A vertical square surface as shown in the figure as shown in the figure has its upper edge horizo...

Q: Example 4-2 :A rigid tank of 1 m' contains nitrogen gas at 600 kPa, 400 K. By mistake someone lets 0...

Q: As an oil well is drilled, each new section of drill pipe supports its own weight and that of the pi...

Q: A 2024-T4 aluminum tube with an outside diameter of 3.8 in. will be used to support a 36-kip load. I...

Q: Given that F1 = 600 N and Ø = 30°. See figure MECH 5.1. Solve the resultant force acting on the eye...

Q: The coefficient of friction between the block of mass m, = 3.00 kg and the surface in the figure bel...

Q: A steel rod with a cross-sectional area of 199 mm2 is stretched between two fixed points. The tensil...

Q: (42) The two uniform bars shown in Fig. (25) are of equal length and equal mass. Determine the equat...

Q: The left limb of a U-tube mercury manometer is connected to a water pipe line, with the mercury leve...

A: P = Po + ρgh

Q: platform weighing machine

A: From very early times, civilizations used weighing machines in business transactions. Over the years...

Q: Calculate the weight of block A shown in the figure. 37 530 36 N

Q: A tank full of water is designed with ends in the shape of an isosceles triangle with height 20 mete...

A: GivenA tank with ends in the shape of an isosceles triangleH=20mW=9m at the top

Q: The force R is the resultant of the forces F1, F2 and F3 acting on the rectangular plate. See figure...

Q: PROBLEM 17.116 A sknder nod of kengthL and mass m is released from rest in the position shown. k is ...

A: Given Slender rod To find Coefficient of restitution Proof of bouncing

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Problem 2 A solid steel shaft 5 m long is stressed at 80 MPa when twisted through 4°. Using G = 83 GPa, compute the shaft diameter and torsional stiffness. What power can be transmitted by the shaft at 20 Hz? Answers: 138 mm, 591.2 kN.m/rad and 5.19 MW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid steel shaft 4.5 m long is stressed at 63 MPa when twisted through 2.7°. Using G= 80 GPa, compute the shaft diameter. What power can be transmitted by the shaft when rotated at 660 rpm? T
A hollow simple supported shaft 3m made of steel with di/do of 0.6. The shaft is subjected to a bending force of 4 KN and transmits 52 KW with 150 rpm. Find the outer and inner diameter of the shaft, if the ultimate shear stress of 600 MPa and allowable compression stress of 100 MPa, tack safety factor 7.
A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3300 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 590 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp psi Save for Later Attempts: 0 of 1 used Submit Answer
A solid steel shaft 5 m long is stressed at 80 MPa when twisted through 4°. Using G = 83 GPa, compute the torsional stiffness. Answer: 591.2 kN.m/rad
Write legibly, provide manual step by step solution, and diagram for below given problem. A 2.5 in diameter 10 spline shaft ( d= 0.86D, w= 0.156D, h= 0.07D ) to slide when not under load has a compressive force of 2500 lb. Find the torque applied if hub length is 1 1/2 in. Ans. 2906.25 in-lb
Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque 325(T).