A sluice gate is used to control and measure the discharge in an open channel, when the upstream and downstream water depths are 1.0 m and 0.2 m respectively. Calculate the discharge in the channel

Q: Pls answer asap. Complete solution with figure. Determine the discharge in a rectangular channel…

A:

Q: Compute the total discharge in the stream based on thẻ given cro 12 18 24 30 distance, m 1.6 1.9 2.5…

A: Assuming same the cross-sectional dimensional through: The average Velocity will be,…

Q: The water depth upstream of a sluice gate is 0.8 m and the depth just downstream (at the vena…

A:

Q: The uniform flow is achieved in wide rodangular channal at depth 1.2m to cause a flow velocity 1.5…

A:

Q: Calculate the value of the hydraulic radius for flow in an open channel where the bottom of the…

A: Figure of the channel according to given statement:

Q: The flow rate in a channel with area of 25 m2 has an average depth of 3 meters - was recorded at…

A: Given that  Flow rate =Q= 200 m3/s   Area of channel= A= 25 m2  Depth = y= 3 m first of all we have…

Q: Uniform Flow Q.15 Calculate the Froude number of a most efficient rectangular channel having depth…

A: Most efficient rectangular channel- Depth of flow y=1.65 m, Discharge Q=4.56 m3/s. To Find- The…

Q: Calculate the approximate specific energy of a trapezoidal channel having a bottom width of 5m,…

A: Given data- A trapezoidal channel- Bottom width b=5 m, Side slope 1:1, Depth y=2 m, Discharge Q=15…

Q: c. Discuss how the hydraulic design of the Overflow weir, Morning glory spillway and Siphon spillway…

A:

Q: Question 3 Calculate the critical depth corresponding to a discharge of 8.5m3/sec in a rectangular…

A: Given that :- Discharge = Q = 8.5 m3/s width = B = 3.6 m To calculate the critical depth

Q: 1- There following data are obtained from streamflow measurement in a river cross section. Estimate…

A: distance from left corner 01234567water depth01.353.315.09.05.383.781.78flow velocity at 0.2…

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

A:

Q: Calculate the critical depth corresponding to a discharge of 8.5m³/sec in a rectangular channel of…

A: Given: Discharge, Q = 8.5 m3/sec Rectangular channel width, B = 3.6 m

Q: (a) Define and explain uniform flow. How is open channel flow different from pipe flow? (b) Under…

A:

Q: Using the data obtained with the help of a current meter having constants a=0.05 and b=23 as given…

A: The cross-sectional area is the area of a two-dimensional object that is obtained when a…

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

A: Given data- A wide rectangular channel- Normal depth is increased by 10%, To Find- The % increase in…

Q: n a 1:50 model of a spillway, the discharge was measured to be 0.3 m³/s. The corresponding prototype…

A: Given: A 1:50 model of spillway. The discharge was measured to be 0.3 m3/s. The corresponding…

Q: A Parshall flume is to be designed to measure the discharge in a channel. If the design flowrate is…

A:

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

A:

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

A:

Q: A sewer regulator is equipped with a Cipolletti weir (U.S.B.R. standard trapezoidal weir) to control…

A: Given, Q = 0.85 m3/s

Q: Find the diameter of the sewer pipe to carry runoff discharge (m^3 /sec) at full flow condition for…

A: Area of catchment= 100000 m2 Runoff coefficient C = 0.35  Flow velocity in sever = 1 m/sec  Full…

Q: In a wide rectangular channel if the normal depth of flow is increased by 15%, determine the…

A: ASKED: To determine the percentage discharge corresponding to a given increase in normal depth of…

Q: A small bridge must be constructed across a rectangular channel. Design the possible width of the…

A: To design the width of the channel under the bridge, we need to consider the energy loss due to the…

Q: Calculate discharge for a rectangular Sarda fall having Crest length 10 m Top width 3m and Depth of…

A: Sarda fall  Sarda-type falls are made up of modest falls that result in slow energy dissipation of…

Q: Calculate the difference in critical depth (in cm) corresponding to a discharge of 6.0 m³/s in a)…

A: Given Discharge, Q = 6 m3/sec Rectangular channel width, B = 3 m Critical depth=?

Q: Determine the value of discharge Area of channel=3 m2 Flow velocity= 1 m/s

A:

Q: The flow depth for a triangular channel having (1:2) side slope anc hydraulic depth equal to (0.5 m)

A: Given data: Triangular channel  Side slope 1:2 Hydraulic depth D= 0.5 m

Q: Determine section of Lacey's Regime channel carrying a discharge of 10 m/sec in an alluvium of 0.5…

A:

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

A:

Q: Derive the two formulas for discharge measurement over critical flow structures (for both submerged…

A: Derivation of formula for discharge measurement over critical flow structures for submerged step up…

Q: A circular concrete sewer 1.52m in diameter is flowing 2/3 full has a slope of 1.22m per kilometer.…

A:

Q: Water is to be discharged from an 8-m-deep lake into a channel through a sluice gate with a 5-m wide…

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.