A Single rivet lop joint is to connect 12mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80 N/mm², working stress in bearing in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².

A Single rivet lop joint is to connect 12mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80 N/mm², working stress in bearing in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bolted connection is subjected to a tensile force of P. The diameter of the bolt is d=60 mm. if…

A: Given - Tensile force of 200KN (Not kPa=KNm2 because unit of force is KN or N or lb. ) Diameter =…

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). a 0.692…

A: Solution Given the dia of steel d= 10mm So the area will be A=π/4 * 10² 24=25π mm²

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

Q: Q4. A single strap single riveted butt joint joins two plates (12 mm and 10 mm), when the diameter…

A: Given: Plate thickness = 12 mm and 10 mm diameter of rivet = 14 mm c/c of adjacent rivets = 60 mm…

Q: The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the…

A: First we need to find the value of yield strength using steel through internet.

Q: The rigid beam is supported by the two bars shown in a horizontal position before the load P is…

Q: 1. Two plates are connected by bolts as F F 150 mr shown in the figure. Compute the bearing stress…

A: To calculate the bearing stress in each bolt of the given bolted connection. Given, Load acting on…

Q: What would be the temperature at which the bar will have a compressive stress of 3 MPa given that at…

A: Elongation due to temperature change δT=Lα(ΔT)ΔT=T2-T1=T2-(-20)=T2+20

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

A: The given figure is shown below:

Q: 3. A flat steel bar, I inch wide by 1/4 inch thick and 40 inches long, is bent by couples applied at…

A: Given: Required: Stress in bar Magnitude of couple

Q: In the figure shown, determine the normal stresses at AD + and BC + , shearing stress at bolt D • ,…

A: From the figure : Taking the moment at C: ∑Mc=0200.25+0.4-RD0.4=0Simplifying the above:RD=32.5 KN…

Q: The axial load 396 kN applied to the lap joint is distributed equally among the three…

A: Answer We are given Axial load = 396 KN bolt diameter = 20.6 mm bolts width of plate w = 135.4 mm…

Q: A bolted connection s

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 700 mm in diameter. What minimum…

Q: In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm…

A: Lap joint: When one plate is overlapped on the other plate and both the plates are riveted by a…

Q: A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of…

Q: A Single rivet lop joint is to connect 12 mm thick plates by providing 20mm dia, rivet at so mm…

A: Given Data Thickness of plate (t) = 12mm Diameter of rivet (d) = 20mm Pitch (P) = 50 mm Working…

Q: MAXIMUM SHEAR STRESS

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

21.
A Single rivet lop joint is to commect 12 mm
thick plates by providing 20mm dia. rivet at
somm pitch. determine the strength of the
joint and joint efficiency.
Take working stress in shear in rivets = 80 N/mm²,
working stress in beaning in rivets = 250 N/mm²
and working stress in axial tension in plates.
= 150 N/mm².

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

#1 will upvote anyone who will answer correctly. Thanks
I need the answer quickly
The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.-
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
can someone help me with this? Thank you
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 3/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 3/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 6.0 kips. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
jp
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 5/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 5/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 8.0 k. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
What is the safe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit stress in shear is 13,600 psi? A. 8650 lb B. 9420 lb C. 10,500 lb D. 11,800 lb
Please box the final answer
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
please draw fbd