A single-phase load has an active power of P = 2 kW at 180 V @60HZ and the power factor is cos% = 0.75. This motor is compensated to coso 0.85 using a parallel capacitor (the load is modelled as series RL). Determine: a. Reactive power and apparent power before compensation using power factor b. Current before compensation C. R, XL and L values of the load d. Reactive power and apparent power after compensation e. Find the reactive power difference between compensated and uncompensated status (which will give the capacitor power) and calculate XC and Cusing the power difference value f. Simulate the uncompensated and compensated circuits. Plot voltage and current on components and calculate the phase shift of the signals from Vin g. Plot Vin and lin comparison for both circuits and show/calculate the phase angles for circuits

A single-phase load has an active power of P = 2 kW at 180 V @60HZ and the power factor is cos% = 0.75. This motor is compensated to coso 0.85 using a parallel capacitor (the load is modelled as series RL). Determine: a. Reactive power and apparent power before compensation using power factor b. Current before compensation C. R, XL and L values of the load d. Reactive power and apparent power after compensation e. Find the reactive power difference between compensated and uncompensated status (which will give the capacitor power) and calculate XC and Cusing the power difference value f. Simulate the uncompensated and compensated circuits. Plot voltage and current on components and calculate the phase shift of the signals from Vin g. Plot Vin and lin comparison for both circuits and show/calculate the phase angles for circuits

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
what is the use of DC/DC tension converter DC/DC booster MT3608
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
١-The PMSM used in the industry due to: a- Their low noise. b- Their easy control arrangement. c- Their efficiency. 2- The BLDCM used in the industry due a- Their low noise. b- Their easy control arrangement. - Their efficiency. 3- The (PMSM) supplied by: a- DC voltage. b- AC voltage of sinusoidal waveform. C- AC voltage of trapezoidal waveform. Choices
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, SCT RL D. llle ண
Damping ratio quettion.
C. A single phase full converter feeding RL load has the following data: source voltage 230V(RMS), SOHZ.R-2.52 L=very large, firing angle -30"f the load inductrance is large enough to make the load current constant then i Sketch the time variation of sounce voltage source current, load voltage, load current current through one thyristor and voltage across it H. Compute the average value of load voltage and load current, Derive the formula.
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 45 degrees. The maximum RMS and average current ratings of the thyristor are equal to: Select one: O a. 33.94A and 21.6A O b. None of these O c. 24A and 10.8A O d. 48A and 26.09A Clear my choice
A single phase Full-wave controlled rectifier is connected to center- tapped transformer that supplies 220v, 50HZ. The load resistance equal its inductive reactance. A- Find the henrys of the load when the thyristors with zero delay and the de ammeter rcads 4.2 A in the load. B- Find the average and rms output voltage at firing angle a-60 when the thyristors is forced commutation at angle 170° at the same R-L load. C- Find the average of output current at the same conditions in point (B). D- Find the form factor and ripple factor.