A simple gear train has 2 spur gears. The input gear has 24 teeth and the output gear has 106 teeth. The input rotates at 1,556 rev/min clockwise. Calculate the gear ratio and the output speed in rev/min. The input torque is 17 15 Nm and the efficiency is 0.8465%. Use speeds from the previous question to calculate the absolute value of the holding torque in Nm.

A simple gear train has 2 spur gears. The input gear has 24 teeth and the output gear has 106 teeth. The input rotates at 1,556 rev/min clockwise. Calculate the gear ratio and the output speed in rev/min. The input torque is 17 15 Nm and the efficiency is 0.8465%. Use speeds from the previous question to calculate the absolute value of the holding torque in Nm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and n5) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. 75, 100 2007 In Out 4
A gear box has an input speed of 1800 rev/min clockwise and an output speed of 400 rev/min The input power is 25kW and the efficiency is 90%. Compute the input torque the output power 3. the output torque
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
I want to solve these five points
Pls explain to step by step and i will rate your answer immediately. Thanks
Please help me finding this question. Power = 6 kW
The maximum sliding velocity of the teeth of two gear wheels in mesh is 0.32 m/s. The wheels are of module 5 mm and have 32 and 44 teeth respectively. The addendum for each wheel is 1.2 times the module and the pressure angle is 20°. Calculate: 2.1. The number of teeth in contact. 2.2. The angular speed of each wheel.
In the pulley system shown in the figure, while the P gear rotates in the direction of 1 with its angular velocity, find the direction and angular velocity values of the other gears. Hint: The speed of the gears is equal at the point of contact. The speed of a belt is the same at all points.( w=3 rad/s , rk=0.8m ,rL=0.2 m ,rM=0.2m, rN=0.5m rP=0.4m rR=0.4m
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio
An electric motor develops 8 HP at 2652 rpm. An 19 tooth gear is fitted to its output shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 92 Nm is required? Answer: Next page page Finis Time 9Type here to search