A sieve analysis was conducted on a The results are provided in the table. . .gram sample of a food material. Questions 1. Calculate the percentage passing for each sieve. 2. Plot the cumulative smaller and larger fraction versus particle size on semilog plot.

A sieve analysis was conducted on a The results are provided in the table. . .gram sample of a food material. Questions 1. Calculate the percentage passing for each sieve. 2. Plot the cumulative smaller and larger fraction versus particle size on semilog plot.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2.1 Liquid limit (LL) Number of Mass of container and wet specimen (g) Mews Mass of Mass of…

A: We are given Liquid Limit and Plastic limit data (2.1) Liquid Limit It is a minimum water content at…

Q: Calculate the BOD, Initial Sample D.O. = 8.1 mg/L 5-Day Sample D.0. = 2.1 mg/L Vol. Of Sample in 300…

A: The given data is: Initial Sample D.O=8.1 mg/L 5-Day Sample D.O=2.1 mg/L Vol. Of Sample in 300 mL…

Q: The 3 day BOD of a sample is 75mg/l with k(base e) is 0.345/day. The amount of BOD remaining in the…

A: Given 3 day BOD 75 mg/lConstant 0.345/dayTo find out BOD after 8 days

Q: PROBLEM: A dry soil is mixed with 17% by mass with water and compacted. The volume of wet soil is…

Q: Calculate percentages passing, total percentages retained, or percentages in various size fractions…

A: To calculate the percent retained in each sieve, total percentage retained and the percent passing.…

Q: O D. One sample z-Test for proportions

A: In order to test the legitimacy of the manufacturer's claim,it is clear mentioned that to use the…

Q: ne % of aravel (n

A: % sand =Retained on between No 200 and no 4 sieve% gravel =Retained on 4.75mm sieve (no 4 sieve)so,

Q: 1. Calculate D10 and Cu for graph "B". Indicate if the sample is well or poorly graded. Explain your…

A: Particle size distribution curve is given. We need to calculate D10 and Cu for soil A and B

Q: Q1: The results of a standard Proctor test are given in the table. The volume of the proctor mold…

A: Standard proctor test is a laboratory method used to determine the moisture content at which soil…

Q: If the particle passing on sieve No.200 is 72%, passing on sieve No. 4 is 90%; what is the % of…

A: Given Percentage of passing on sieve no 200 = 72 Percentage of passing on sieve no 4 = 90

Q: Q30: Discuss the different types of defects in the soil masses (150 - 250 words).

A: Different types of defects in soil masses.

Q: Using the data for a sieve analysis shown below, the percent retained on the 2 mm sieve is most…

A: Given, Sieve analysis data To find : Percent mass retained on 2.36 mm sieve

Q: Write step by step the calculations, if it is necessary. a. Identify the type of sieving series. b.…

A: a. There are two type of sieve process. They are dry and wet sieve analysis. In dry sieve analysis…

Q: A sample of dry coarse-grained material was taken through a nest of sieves and the following results…

Q: for

A: OSTWALDS EQUATION:time=A×μρμ=viscosity=0.98poise=0.98×0.1 Nsecm2ρ=0.02gcc=20kgm3 A=?

Q: A sample of dry coarse-grained material of mass 1 kg was shaken through a nest of sieves and the…

A: Solution Given that Mass= 1kg

Q: 5-Draw the relationship between percent passing and sieve size. and discuss. 6-what are the cause of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: %; what is the % of gravel. (provide the ans ly)

A: Given that % passing on sieve no. 200 = 72 % % passing on sieve no. 4 = 90 %

Q: making

A: Given sieve analysis Write the corresponding sieve sizes in 'mm' Sieve No Sieve size #4…

Q: Find the water content in the following calculations 1- Liquid limit Determination: Weight of can+…

A: The given data is shown below:

Q: 5. A water sample has been analyzed. Upon titration with EDTA, the following results were gathered.…

A: Given, Volume of water sample = 10 ml Volume of CaCO3 = 5 ml

Q: 7. . Find the grain-size (gradation) distribution of the following: a. Original dry mass of sample…

A: Answer We need to find percent finer in each sieve based on the given retained weight and plot grain…

Q: Based on my data and result could be the recommendation and conclusion. This laboratory test is a…

A: Atterburg's limit is also called as consistency limit. The different types of consistency limits…

Q: A seeded BOD analysis was carried out about a high strength food processing wastewater. 20 ml…

A: initial Dissolved Oxygen of Seed Only Bottle Initial Dissolved oxygen of sample and Seed Bottle

Q: • Problem 2- . The following are the results of a sieve analysis. Determine the percent finer than…

Q: Grain size distribution Homework: Following are the results of a sieve analysis: Sieve No. 4 10 20…

A: SIEVE NO. SIEVE SIZE in (mm) Mass of soil retained on each sieve percentage of weight retained (%)…

Q: е. 650 ton of Sample1 and 150 ton of Sample 2 are available. How many Kg of particle size bigger…

A: e. Calculate the % of retained for each sample. Calculate the same proportion with 650 ton of Sample…

Q: In the picture is a distribution graph of the sphericity of a sample of aggregate materials. The…

A: In the picture is a distribution graph of the sphericity of a sample of aggregate materials. The…

Q: 3 The below results are obtained from a sieve analysis done on a sample with dry mass of 1550 g. The…

A: The given data is shown below:

Q: From the results of a sieve analysis given below compute for the effective size of D10, D30 and D60

A: Results of sieve analysis are given as Sieve number Mass retained (g) 4 0 10 40 20 60 40…

Q: The fluid displacement technique is used to find the porosity of a certain core sample. The sample…

Q: imit Test mber 1 er of Blows 39 30 23 of Wet 22.24 21.19 21.2 Container i of Dry Soil 20.10 19.28…

Q: 1. A settling column analysis is performed on a dilute suspension of particles from water. The…

A: Tabulate the time and fraction of particles settled.Time required to settle (min)Fractions of…

Q: In an experiment to calibrate the Hydra Probe soil moisture meter by volume the results were as…

A: Calibration equation is determined by regression analysis as, Plotting instrument reading on y axis…

Q: In a falling head permeameter test, the head drops by 5 cm in 10 minutes from the initial head of 30…

Q: Based on my data and result could be the recommendation and conclusion. This laboratory test is a…

A: Given data, Average specific gravity = 2.47

Q: Solve the question in the image.

A: Over all efficiency for the control device can be given asηo=∑mass ratio×efficency %

Q: The 3 day BOD of a sample is 75mg/l with k(base e) is 0.345/day. The amount of BOD remaining in the…

A: Given, 3 days BOD= 75mg/l k= 0.345/day (Base e) Find out: Amount of BOD remaining after 8…

Q: The initial length and diameter of all three samples are in a ratio of 2:1, with the length being…

A: Given:- The ratio of the initial length and diameter of all three samples = 2:1 The value of the…

Q: Percent Passing 90 80 70 60 50 What would be the closest number for the uniformity coefficient (Cu)…

A: Given InformationTo find the value of Cu from the above graphs

Q: Given the following sieve analysis data, determine the percent passing on the No. 100 sieve. Sieve…

A: The objective of the question is to determine the percent passing on the No. 100 sieve given the…

Q: For the measurement of the BOD of a wastewater sample from textile industry, five different…

A: Given- Assume K=-0.234day-1 t=5

Concept explainers

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The results of a grain-size analysis is given below. Plot the grain-size distribution curve and determine what is the median size (D50)? US Sieve No. Size of opening (mm) Mass retained (g) 3/8 in. 9.5 0 No.4 4.75 42 No.10 2 146 No. 40 0.425 458 No. 100 0.15 218 No. 200 0.175 73 Pan NA 63 0.1mm 0.7mm 1mm 2mm
Kindly give me ALL right solutions
In a falling head permeameter test, the head drops by 5 cm in 10 minutes from the initial head of 30 cm. The cross-sectional area and height of the sample is 50 cm² and 5 cm respectively. Calculate the additional time (in minutes) required to run test the so the head of the sample falls to 20 cm.
Table 1 shows the result of the sieve analysis for the material of asphalt concrete (AC) mixture. Analyze the result of the sieve analysis by plotting the gradation curve of the sample. Conclude either the sample that been sieve is fulfill the requirement or not? Q4. Table 1 Sieve size (mm) Mass retained (g) Gradation limit for AC 14 20.0 0.00 100 14.0 69.60 90- 100 10.0 296.10 76- 86 5.00 433.70 50 - 62 3.35 170.50 40 - 54 1.18 321.20 18 - 34 0.425 212.00 12 - 24 0.150 135.10 6- 14 0.075 49.30 4-8 PAN 72.80
A Standard Proctor Test was completed according to Method A described in Chapter 12. The following laboratory data was obtained: Mass of mold = Mass of moist specimen and mold = Volume of compaction mold = Mass of container= 51.5g Mass of container plus moist soil= 261.85g Mass of container plus oven-dried soil= 231.83g 1.98 kg 3.718 kg 0.0009438m3 Determine the Dry density of compacted specimen. (expressed in Mg/m3, 3 decimal places) Your Answer:
Answer in three decimal places please
Problem The following are the results of a sieve analysis: a. Determine the percent finer than each sieve and plot a grain- size distribution curve. b. Determine D10, D30, and D60 from the grain-size distribution curve. c. Calculate the uniformity coefficient, C. the coefficient of gradation, Co. U.S. sieve no. 4 10 20 40 60 80 100 200 Pan Mass of soil retained (g) 0 44 56 82 51 106 92 85 35
What is the moisture content for test 1? Round off your answer to two decimal places. No need to indicate the percentage sign. Plastic Limit Test No. 1 2 Can No./ID A B Mass of can (g) 13.30 14.50 23.86 32.10 Mass of can + moist soil (g) Mass of can + dry soil (g) moisture content 22.27 29.20 Answer:
N2
True or False: When comparing two samples of equal mass, the number of particles in each sample is inversely proportional to the size of the particles cubed. Select one: O True O False True or False: PM 10 measurements only account for particulate matter exactly 10 microns in diameter large. Select one: O True O False
Please help me to explain the results of the Sieve Analysis for question #5 & explain how I might go about writing a conclusion.
A Standard Proctor Test was completed according to Method A described in Chapter 12. The following laboratory data was obtained: Mass of mold = Mass of moist specimen and mold = Volume of compaction mold = Mass of container= 51.5g Mass of container plus moist soil= 261.85g Mass of container plus oven-dried soil= 231.83g 1.98 kg 3.718 kg 0.0009438m3 Your Answer: 4 Determine the Moist density of compacted specimen. (expressed in Mg/m³, 3 decimal places)