A side hammer is collected with both shaft and journal sliding support, as illustrated in belowFigures (a) and (b), where this system employed to crashing a raw material of cement in the cementfactory. Determine the following:Ø40Case-AShaftJournal Slide Support100220Side Hammer5016 KNB16 KNCase-B1. Maximum stress of this system at Case-A.2. Maximum Stress of this system at Case-B.DO NO SCALE DRANGBRLAK SHARP3. Crashing stress of journal sliding hole.Hint:a. Use APPENDIX-A to help you in evaluating your answer, all dimensions based on SI-Units.b. R/J of side hammer is 0.764325 mm'.A4APPENDIX-A

Answered: Image /qna-images/answer/2e2b2e28-aee2-452a-8dab-4a49e653e52e.jpg

A side hammer is collected with both shaft and journal sliding support, as illustrated in below Figures (a) and (b), where this system employed to crashing a raw material of cement in the cement factory. Determine the following: Shaft Journal Slide Support Side Hammer 16 AN B 16 KN 1. Maximum stress of this system at Case-A. 2. Maximum Stress of this system at Case-B. 3. Crashing stress of journal sliding hole. Hint: a. Use APPENDIX-A to help you in evaluating your answer, all dimensions based on SI-Units. b. R/J of side hammer is 0.764325 mm.

A side hammer is collected with both shaft and journal sliding support, as illustrated in below Figures (a) and (b), where this system employed to crashing a raw material of cement in the cement factory. Determine the following: Shaft Journal Slide Support Side Hammer 16 AN B 16 KN 1. Maximum stress of this system at Case-A. 2. Maximum Stress of this system at Case-B. 3. Crashing stress of journal sliding hole. Hint: a. Use APPENDIX-A to help you in evaluating your answer, all dimensions based on SI-Units. b. R/J of side hammer is 0.764325 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3: . A crank built up from cylindrical sections by welding required a loading of 250 lb to overcome the resistance when in the post- tion shown. (a) Compute the maximum normal and shear stresses induced in the section A-A. (b) Determine the maximum shear stresses induced in parts I, II, and III. Ans. (a) (max) = 29,000 psi, T(max) = 15,000 psi (b) 10,550 psi for part I, 6880 psi for II, 15,000 psi for III --A III II 1 Dia. Dia. Fig. 2-38 250 lb 150 "Dia.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
A force of 100N is applied to the free end of a restrained beam, shown in the figure. The wall thickness is 2 mm from the upper and lower walls (1-6, 2-3, 4-5) and 4 mm on the side walls (1-2, 5-6). Calculate the normal stress distribution and the maximum stress in the middle section.
HW A Solid Steel bar of dlameter 6omm andlengtj2. 350mmis p laced inside analuminum cylinderof Insie diameter Fommm and out side dlameter lomm, a compressive load of loo0 law is applled on the assembi n find the stresses in the barand the cylinder? take e Est= 200GPA and EAl= FoGla- SAL? D=u.25 %D লি Cover Plate 0.25mm di 350mm A lum. cylinder Steel bar
The hollow core panel is made from plain stone concrete. Determine the dead weight of the panel. The holes each have a diamenter of 4 in.
1.0. size= Q4: Estimate the permissible stress for a Ck 60 steel gear shaft of 100 mm outer diameter with strength 660MPa tested for 10 mm diameter shaft. If the impact safety factor is 1.5, and the load error factor C assumed 25% load additional due to inertia forces and at 300 °F elevated temperature. chnical Univer raq
Q1 : For a yield strength of 50 kpsi find the factor of safety at point A using the maximum shear stress theory. [Ans 2.34] 1.25 in.- 60 in.- 200 Ib 200 Ib -24 in.- 24 in.- 1.5 in. Web and flange thickness 0.125 in
Determine the cracking moment for the figure shown if it is a normal weight concrete with fc=4,000psi. 8 in. 8 in. 24 in. 3 #10 8 in. 3 in.: ⒤갓⒤갓⒤뀐⒤뀐⒤ 6 in. 15 in. -16 in.-
Determine the bending stress and shear stress in the problem below.
Use fr ( Modulus of Rupture) = 0·7√ f'c a = 500mm b = 200 mm f'c = 21 mpa C = 150mm d = 500mm e = 150mm Concrete density (normal) = 24 kn/m² a) Determine the gross moment of Inertia, in x10 mm" b.) Determine the cracking moment, in kN.m c.) betermine the live load that the beaum can carry if it has a simple span of 10 meters in KN.m. b —a—
Note: ... HP12X53 Ag=15.5 in^2 rx = 5.04 in ry = 2.86 in 16' HP 12 x 53 A572 Grade 50 From Situation 1: c. Compute the Euler's Buckling load (kips) Round your answer to 3 decimal places. Add your answer From Situation 1: d. Governing Nominal Compressive strength based on AISC E3-2 or E3-3 (kips) Round your answer to 3 decimal places. Add your answer
R1-5. Determine the average punching shear stress the circular shaft creates in the metal plate through section AC and BD. Also, what is the average bearing stress developed on the surface of the plate under the shaft? C 40 KN -50 mm- -60 mm- -120 mm B D $10 mm