A shaft running at 200 r.p.m is to drive a parallel shaft at 300 r.p.m. The pulley on the driving shaft is 60 cm diameter. Calculate the diameter of the pulley on the driven shaft: (1) Neglecting belt thickness. (2) Taking belt thickness into account, which is 5 mm thick. 3) Assuming in the latter case a total slip of 4%.

A shaft running at 200 r.p.m is to drive a parallel shaft at 300 r.p.m. The pulley on the driving shaft is 60 cm diameter. Calculate the diameter of the pulley on the driven shaft: (1) Neglecting belt thickness. (2) Taking belt thickness into account, which is 5 mm thick. 3) Assuming in the latter case a total slip of 4%.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The shaft below is an engine component that is rotating. It is machined from an unknown ductile…

A: Solution: Given Data: Sut=900 MPaR=0.99f=0.9d=0.1 m

Q: groove is of wi dth r. mine per unit sliding distance when, W = 0,2 mm, and H = 75 MPa.

A: To given that load (W)=50N Diameter (D)=5mm Width(r)=0.2mm Hardness…

Q: Fig. 3 shows the load torque variation for one cycle of a shaft driven by a constant torque With an…

A: Here given we have b=2tCs=0.2δ=8050 kg/m3I=125 kgm2Cycle time =4π

Q: Q3 A solid shaft produced from 1045 steel must be 200 cm long and must survive continuous operation…

A: Given data: The length of the shaft, L=200 cm. The time of operations, t=1.5 years. The load…

Q: A drilling machine is capable of drilling 30 holes of 20mm diameter per minute in a 16mm thick steel…

A: please refer handwritten solution

Q: Example 3: A composite spring has two close coiled helical springs connected in series; each spring…

Q: Explain the significance of understanding the effects of applying a torsional loading to a long…

A: EXPLANATION: The torsional strain on a circular cross-section causes the cross-section to twist…

Q: 1. A 1 % in. by 7/8 in. key is to be designed for a 12.7 cm shaft which will transmit power of 187.2…

Q: A hollow bronze shaft of 75 mm outside diameter and 12.5 mm thick is coaxial with a solid steel…

Q: A solid cylindrical shaft 50 cm long is used for a transmission of mechanical power at a rate of 35…

A: Given Data P=35 kW N=2000 rpm Allowance shear stress S= 8.3 MPa

Q: .Assume the shafts are straight, the material is homogeneous and the shafts are made of the same…

A: Solution:- Calculation:- 1. for equal stress 16 Troundπd3 =4.8Tsquared3Tsquare = Tround164.8π…

Q: An alloy steel Metric 10x1.5 screw (10 mm diameter, pitch p = 1.5 mm) is to be turned into a…

Q: (a) maximum principal stress theory (b) maximum princ

A: given: in the design of shafts made of ductile materials subjected to twisting moment and bending…

Q: In a torsion text, the specimen is a hollow shaft with 40 mm external and 20 mm internal diameter.…

A: Data given- D = 40 mm = 0.04 m d = 20 mm = 0.02 m T = 2 kNm Angular twist = 0.5° = 0.5×π/180…

Q: The shaft below is an engine component that is rotating. It is machined from an unknown ductile…

A: Calculate the maximum bending moment. MB=55.50.5=27.75 kNm

Q: 24 4. A solid shaft of 35 mm diameter is subjected to an applied torque of 320 Nm. Calculate the…

A: GivenD=35mmT=320Nm=320×103 Nmmd=17.5mm

Q: An automotive shaft manufacturing facility wants to reduce the material cost of the shaft. Propose a…

A: When we want the shaft to carry shear stress on the outermost edge, the most preferred one is hollow…

Q: In a torsion text, the specimen is a hollow shaft with 40 mm external and 20 mm internal diameter.…

Q: A solid shaft transmits 1.7 kW of power at 4.4 Hz. What is the smallest safe diameter of the shaft…

A: The expression to calculate the maximum shear stress is…

Q: (5) A 76mm solid shaft is to be replaced with a hollow shaft of the same torsional strength.…

A: When an amount of force applied on the object, then it has the tendency to rotate that object about…

Q: 2. A solid circular shaft has a diameter of 2 in. The shaft, in its current geometry, does not have…

A: The process to achieve a Three-fold increase in the polar moment of inertia of the solid circular…

Q: An engine shaft running at 1,748 r.p.m. is required to drive a machine shaft by means of a belt. The…

Q: Question 4 A shaft used for a water pump has a diameter of 50 mm and a length of 0.7 m long and is…

A: GIVEN DATA- a) Diameter D=50mm , L=0.7m , G=90GPa , Torque T=1200Nm b) Hollow shaft with internal…

Q: An engine shaft running at 4.5r.p.s. is required to drive a machine shaft by means of a belt. The…

Q: The shaft below is an engine component that is rotating. It is machined from an unknown ductile…

A: Solution: Given Data: Sut=900 MPaR=0.99f=0.9

Q: Select the diameter for a solid steel shaft that is to transmit 60 HP at 850 rpm without exceeding…

Q: A 1 m length of 50 mm diameter steel bar is subjected to a torque of 230 Nm. Calculate the maximum…

Q: Determine the magnitude of the principle stress

A: Given; internal diamter(d)=100 mmthickness=5 mmpressure=10 MPatorque(T)=2000 Nm Acc. to question ,…

Q: A solid steel shaft is subjected to a variable torque whose maximum value is 710 N-m. For a fatigue…

Q: (2) A 1015 hot-rolled steel circular operating in an environment of 485 °F. If S-110ksi, S=50 ksi…

A: Given: The type of material = 1015 hot rolled steel at 485°C The ultimate strength of shaft, Sut =…

Q: The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner…

Q: A aluminium rod of diameter 45 mm is subjected to a torque of 79 Nm. Assume one end is fixed of the…

A: Given:Diameter of rod,d=45mm=0.045mSo,Radius of rod,r=d2=0.0225 mTorque on rod=79NmLet the hear…

Q: A pressure vessel has an outside diameter of 50 mm and a wall thickness of 2mm and is subject to an…

A: Given data, Outside diameter of pressure vessel, Do = 50 mm Thickness of the pressure vessel, t = 2…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

A shaft running at 200 r.p.m is to drive a parallel shaft at 300 r.p.m. The pulley on the driving
shaft is 60 cm diameter. Calculate the diameter of the pulley on the driven shaft:
(1) Neglecting belt thickness.
(2) Taking belt thickness into account, which is 5 mm thick.
3) Assuming in the latter case a total slip of 4%.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I keep getting a massive inner diameter for this how do I solve it?
The speed of a 250-mm-wide grinding wheel is 2000rev / min. use a bore of 20 mm, v = 0.24, and a maximum mass of %3D 3320 kg / m3, and obtain a maximum tensile stress at this speed.Assume that the material is isotropic.
A 30 mm diameter shaft transmits 10 kW at 600 rpm. It was found that a stress raiser exist whose stress concentration factor in torsion is 2.50. Compute the factor of safety of this shaft if its shear yield strength is 150 MPa.
help please how can i solve this
Example 7.5: (Numerical problem of a circular shaft) A circular shaft 10 cm diameter and 1.1 m length is required to transmit power with a maxi- mum angle of twist of 3°, (a) What is the maximum possible torque that can be transmitted by this shaft? (b) Find the maximum shear stress induced. (c) Find the maximum possible power transmitted for N = 1500 rpm. Given that modulus of rigidity G 8% 101M Pa.
A shaft is loaded by a torque of 5 KN-m. The material has a yield point of350 MPa. Find the required diameter using(a) Maximum shear stress theory(b) Maximum distortion energy theoryTake a factor of safety of 2.5.
A single solid circular shaft 400 mm diameter running at 250 RPM, is to be replaced by two hollow circular shafts of equal size running at 150 RPM and developing 50% additional power. The internal diameter of hollow shaft may be taken as one third of their external diameters. If the working stress of the new shaft is 30% greater than that of the former, find the external and internal diameter of hollow shafts.
I need the answer as soon as possible
A 2-cm square cross-section steel part having a Brinell hardness of 200 and a length of 5 cm is to be ground by adhesive wear using a tool of electroplated chromium with a square head of 2 mm x 2 mm. If the normal force applied is 20 kN and the depth to be removed from the surface is 4 mm, determine the number of passes needed (parallel to the length direction) for poor lubrication. Select one: O a. N = 1570 O b. N = 2093 O c.N = 6278 O d. N = 3139
Asap please
What is the torque applied, in Nm, to a 91 mm shaft if the resulting shear stress on the outside surface of the shaft is 52 MPa? Note: Do not include units in your answer Answer: