A secondary timber member in a warehouse is made of seasoned MGP10 grade timber. The length of the member is 3.0 m. The applied tension loadings to be considered are: 5 kN (permanent) (dead load) 5 kN (permanent) (live load) 5 kN (wind load) The designer is going to use 6 bolts of 10mm at each end connection in two rows. The holes should be 1mm more than bolt diameter. The ware house is located in Darwin. According to AS1720, is the section of 140x45mm adequate to resist the applied tension forces or not?

A secondary timber member in a warehouse is made of seasoned MGP10 grade timber. The length of the member is 3.0 m. The applied tension loadings to be considered are: 5 kN (permanent) (dead load) 5 kN (permanent) (live load) 5 kN (wind load) The designer is going to use 6 bolts of 10mm at each end connection in two rows. The holes should be 1mm more than bolt diameter. The ware house is located in Darwin. According to AS1720, is the section of 140x45mm adequate to resist the applied tension forces or not?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.1P

See similar textbooks

Similar questions

Q3 A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten two timbers as shown in figure below. The nut is tightened to cause a tensile load in the bolt of 34 KN. Determine a) the shearing stress in the head of the bolt. B) the shearing stress in the threads, and C) the outside diameter of the washers if their inside diameter is 28 mm and the bearing stress is limited to 6 MPa. 12 mm .16 mm
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset plate as shown in the figure. The tension member is subjected to the following axial loads. Use LRFD Service dead load = 200 kN Wind load = 276 kN Service live load = 260 kN For channel: Fy = 345 MPa For gusset plate: Fy = 248 MPa Fu = 400 MPa Size of E 70 electrodes = 4 mm Ultimate tensile strength of E 70 electrodes = 480; Fw = 0.6(480) Questions : a) Determine the design factored tensile force. b) Determine the length of longitudinal welds "L". c) Determine the block shear strength of the gusset plate.
The largest load P that can be applied is approximately equals: Arca - 0.00126 m oall - 45 MPa a)57 kN B Aren- 0.0007 m b)60 kN Weld allowable strength - 60 kN all - 95 MPa c)67 kN d)50 kN
2. See connection figure below. The rivets is 7/8 in. in diameter. According to the rivert supplier, the allowable stresses for the material are t = 15 ksi and on = 32 ksi. What is the allowable load of the connection? L4 x 3-1/2 W18 x 86 W24 x 117 Girder Beam
Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is connected to a gusset plate using welds 12 inches long, as shown in the figure. The service live load is three times the dead load. Use A992 steel. USE LRFD ONLY, no block shear will occur. What is the Governing Ultimate Tensile Capacity based on Net Fracture Round your answer to 3 decimal places.
4. The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely support a service dead load of 265 kN and a service live load of 555 kN. L 50 102.5 102.5 50 65 65 65 O O 22 veny diameter bolts C310 x 30.8 Iso A36M stool matorial and select a double anglo tonsion member to rosist
Three wood boards, each 4 in. wide, are joined by the 3/4-in.-diameter bolt. If the working stresses for wood are 800 psi in tension and 1500 psi in bearing, find the largest allowable value of the force P.
If you were asked to increase the tensile strength of an existing truss tension member. Which of the following upgrade measures would you recommend? a)weld plates over a certain length of the existing member b)weld plates only near the ends of the existing member c)bolt plates over a certain length of the existing member d)weld plates along the full length of the existing member
A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of nominal diameter 1/2 in in a zig-zag arrangement as shown. Determine the tensile strength capacity Pu of the connection. Review the three limit-states: (a) yielding in the gross area, (b) rup- ture in the overall net tensile area, and (c) block shear strength.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Use attached formula picture for block shear *Please use hand written to solve this problem A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset plate as shown in the figure. The tension member is subjected to the following axial loads. Use LRFD Service dead load = 200 kN Wind load = 276 kN Service live load = 260 kN For channel: Fy = 345 MPa For gusset plate: Fy = 248 MPa Fu = 400 MPa Size of E 70 electrodes = 4 mm Ultimate tensile strength of E 70 electrodes = 480; Fw = 0.6(480) Questions : a) Determine the design factored tensile force. b) Determine the length of longitudinal welds "L". c) Determine the block shear strength of the gusset plate.
11-1. Determine whether the W14 x 34 beam shown in Figure 11-43 is adequate for flexural rupture and flexural yielding at the cope. The steel is ASTM A992, grade 50. 1/2" W14x34 R₁ = 40kips FIGURE 11-43 Detail for Exercise 11-1
3. A 25-mm-diameter bolt having a diameter at the root of the threads of 20 mm is used to fasten two timbers as shown. The nut is tightened to cause a tensile load in the bolt of 34 kN. Determine (a) the shearing stress in the head of the bolt, (b) the shearing stress in the threads, and (c) the outside diameter of the washers if their inside diameter is 28 mm and the bearing stress is limited to 6 MPa. 12 mm 16 mm