A Schottky diode and a p-n junction diode have a cross-sectional area of A= 2. The reverse saturation current density of Schottky diode and a p-n junction diode at T = 300 K $ A/cm² and 3 x 10-12 A/cm², respectively. Determine the forward bias voltage in each diode requi ld diode currents of 1 mA.

A Schottky diode and a p-n junction diode have a cross-sectional area of A= 2. The reverse saturation current density of Schottky diode and a p-n junction diode at T = 300 K $ A/cm² and 3 x 10-12 A/cm², respectively. Determine the forward bias voltage in each diode requi ld diode currents of 1 mA.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
For the diode applied in the circuit has a knee current of 5mA, and a maximum allowed power dissipation of 300mW. What are the maximum and minimum load currents that can be drawn safely from the circuit with constant voltage output Vo of 6V?
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
A silicon diode has a reverse saturation current of 50nA at room temperature (25degrees centigrade). If the operating temperature is raised by 50-degrees centigrade, what is now the reverse saturation current?
With constant current flowing in the forward direction in a small-signal silicon diode, the voltage across the diode decreases with temperature by about 2 mV/K. Such a diode has a voltage of 0.650 V, with a current of 1 mA at a temperature of 25°C. Find the diode voltage at 1 mA and a temperature of 175°C.
A silicon diode with a forward resistance of 100 is connected in series with a 5000 resistor. If an a.c voltage of 20V peak is connected across the series combination of the diode and the resistor what will be the peak value of the current through the diode and the peak output voltage? What will be the peak value of the current through the diode and the peak output voltage if the diode were ideal?
A silicon diode has a saturation current of 5nA at 250C. What is the saturation current at 1000C? For the given series diode configuration, determine Va, Is, and Vz. Si EE 10 V (a)
A silicon diode has a forward voltage drop of 1.2V for a forward DC current of 100mA. It has a reverse current of 1μA for a reverse voltage of 10V. Calculate the: a. Bulk resistance b. Reverse resistance c. AC resistance at forward DC current of 2.5mA