A rotating flywheel of 200-mm radius is braked by the device shown. If coefficient of friction is 0.4 between the wheel and the belt, determine the magnitude of the braking moment due to the vertical force P=120N. 200mm 300mn 30

A rotating flywheel of 200-mm radius is braked by the device shown. If coefficient of friction is 0.4 between the wheel and the belt, determine the magnitude of the braking moment due to the vertical force P=120N. 200mm 300mn 30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PLEASE ANSWER ASAP. WILL RATE IF CORRECT!
SITUATION. The a-t curve for a particle having a rectilinear motion is shown in the figure. At t=0, the velocity is 30 ft/s and the particle is at the origin. a (ft/s²) 0 +10 -10 Determine the maximum velocity in ft/sec. 7 t (sec) 13 -3
A cylinder of 125mm radius rotates concentrically inside a fixed cylinder of 130mm radius. Both cylinders are 300mm long. Determine the viscosity of the liquid which fills the space between the cylinders if a torque of 0.88 N-m us required to maintain an angular velocity of 2n radians/sec. Assume the velocity gradient to be straight line. ( Assuming specific weight of air to be constant at 12 N/m3, what is the approximate height of 2. 3.
Dynamics of Rigid Bodies Answer the question with FBD of yhe figure
1. A4' high, 3' diameter tank whose top is open to the atmosphere is initially filled with water. The discharge plug from the bottom of the tank is pulled out and a water jet whose diameter is 0.5" streams out as shown in the figure below. The average velocity of the jet is V-2gh, where h is the height of water in the tank, measured from the center of the hole (variable), and g is the gravitational acceleration. If it takes 757seconds to drop the water level from 4' to 2 from the center of the hole, how long will it take for the water level into the tank to drop to 1' from the bottom of the tank starting from 2 from the bottom of the tank? Air Water 2' 7575 ĭ, t=? -Dank 2. Determine the Universal Saybolt Viscosity of water at t=3s. Convert the answer to Poise, 3. Convert the pressure gauge reading of 3bar to absolute pressure in psi and kpa. 4. What is the kinematic viscosity of kerosene in ft /s at u=1.64centiPoise? Density of kerosene is 775kg/m? 5. What is the diameter of the other…
The mechanism for a car window winder is shown in the figure. Here the handle turns the small cog C, which rotates the spur gear S, thereby rotating the fixed-connected lever AB which raises track D in which the window rests. The window is free to slide on the track. If the handle is wound at 0.5 rad/s, determine the speed of points A and E and the speed vw of the window at the instant = 40°. - D 20 mm 0.5 rad/s 50 mm B 0 -200 mm -200 mm A E
An accelerometer C is mounted to the side of the roller-coaster car and records a total acceleration of 3.9g as the empty car passes the bottommost position of the track as shown. If the speed of the car at this position is 205 km/h and is decreasing at the rate of 16 km/h every second, determine the radius of curvature p of the track at the position shown. Answer: p= i m 0.65 m
In the figure shown, the load needs to be raised 28 ft. Noting that Gear A is initially at rest and it has a constant acceleration until it reaches 120rpm velocity in 5s, it maintains a uniform velocity of 120 rpm after. Solve for (a) the total time the load was raised at the required height(in seconds). (b) the angle of change of Gear A (in revolution). A 3 in. B 18 in. 15 in. Load
show the fbd and complete soln
The slider bar AB is attached to a collar at A and is fited with a wheel at B. The collar has velocity of 500 mm/s downward and the speed of the collar is decreasing at a rate of 150 mm/s2. The angular velocity of the bar is 3.20 rad's CCW and the velocity of point Bis 0.400 to the right. A 200 mm B Which of the folowing is the conrect acceleration (m/s"2) of point B on bar AB? (A) 0.290 (B) 2.74 (C) 0.372 (D) 0.0391 4,
A rotating shaft with a belt-type brake is shown The static coefficient of friction between the in Fig. brake drum and the brake belt is 0.20. When a 75-lb force P is applied to the brake arm, rotation of the shaft is pre- vented. Determine the maximum torque that can be re- sisted by the brake If the shaft is tending to rotate clockwise. 6 in. P A. B D 3 in. 9 in. 18 in.
3. Starting from rest to an initial angular position 0a = 18 rev, pulley A is given an angular acceleration a = (120A) rad/s², where 0 is in radians. Determine the speed of pulley C. ( Inner hub D is fixed to C and turns with it. ) 150 mm 50 mm 75 mm