a rigid tank contains 2kg of saturated liquid-vapor mixture of water at 250kPa. Initially, three-quarters of the mass is in the liquid phase. an electric resistor placed in the tank is connected to a 110 volt source and a current of 9 amp flows through the resistor when the switch is turned on. Assuming an adiabetic process, determine how long it will take to vaporize (saturated vapor) all the liquid in the tank.

a rigid tank contains 2kg of saturated liquid-vapor mixture of water at 250kPa. Initially, three-quarters of the mass is in the liquid phase. an electric resistor placed in the tank is connected to a 110 volt source and a current of 9 amp flows through the resistor when the switch is turned on. Assuming an adiabetic process, determine how long it will take to vaporize (saturated vapor) all the liquid in the tank.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(f) 500 kg of steam is at 2.0 MPa and 156°C. Determine the phase(s) of the steam present, the volume it occupies, and its enthalpy.
Determine the volume flow rate and the density of carbon dioxide at the inlet and the volume flow rate at the exit of the pipe using (a) the ideal-gas equation and (b) the generalized compressibility chart. Also, determine (c) the error involved in the first case.
Considering water at 250 °C and 800 kPa, determine the value for the partial derivative of using the Redlich-Kwong equation of state. Əv/T
Help please on all
Ten pounds of water at 35oF, and 6.00 lb of steam at 250oF and 20 psia are mixed together in a container of fixed volume. What is the final temperature of the mixture? How much steam condense? Assume that the volume of the vessel is constant with a value equal to the volume of the steam and that the vessel is insulated.
A thermal power plat uses boiler which evaporates 3500 kg of water at 42.5° C into superheated steam at a pressure of 12.5 bar and 275° C. The boiler consumes 500 kg of coal per hour to produce steam. Assume the specific heat of superheated steam as 2.1 kJ/kgK and the calorific value of coal is 32760 kJ/kg. Determine equivalent evaporation "from and at 100° C" and thermal efficiency of the boiler. Use the following steamtable for required values: Saturation Properties Temperature Table hf kJ/kg 171.63 hg kJ/kg 2576.2 hfg kJ/kg t °C bar 41 0.07777 2404.5 42 0.08198 175.81 2575.9 2402.1 43 0.08639 179.99 2590.1 2399.7 10 184.17 31.5 97.3 45 0.09582 188.35 2583.3 2394.9 Saturation Properties Pressure Table hf kJ/kg hg kJ/kg hfg kJ/kg 1998.5 t bar °C 11.0 184.07 781.12 2779.7 12.0 187.96 798.43 2782.7 1984.3 13.0 191.61 814.70 2785.4 1970.7 14.0 195.04 830.07 2788.9 1951.4 15.0 198.29 844.66 2789.9 1945.2
A piston-cylinder device contains satuated water vapor with a constant pressure. The mass and the pressure are listed in the table below. The water is heated by a resistance heater (see the picture below) within the cylinder. The heat supplied by the heater is given in the table below. The cylinder is insulated so there is not heat loss. (a) Determine the enthalpy per unit mass after the water vapor received heat. (b) Determine the temparature after the water vaopr received heat. Parameter Pressure Mass of water Heat supplied by the heater Unit kPa g KJ Value 300 26 7.1 heater
How much energy (BTU) is given off when 5 lbm of saturated steam with a quality of x=1 at 1 psia? How does this compare with the same mass condensing at atmospheric conditions?.
A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston. Heat is added to the system under the isopiestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kW if the mass of the mixture is 22.963 kg/s.
2) In a well-insulated fixed-volume closed vessel, there is initially 5 kg of saturated liquid-vapour mixture water at 100 kPa pressure. In this state, one quarter of the total mass is in the vapor phase. Then, the electric heater in the container operates and a current of 8 A flows through the heater plugged into a 110 V outlet. How long will it take to evaporate all the liquid in the container? Plot the phase change in the T-v diagram showing the saturation curves.
Refrigerant-134a Saturated vapor Saturated liquid A tank occupied by saturated liquid-vapor mixture of refrigerant-134a at 1.8 MPa. If the fraction of the total volume occupied by vapor (Vsaturate vapor/Vtotal) is 0.96, determine quality of the mixture. Present your result cent. (For example, if you find 0.952, enter your result to system as 95.2)
Consider two cases of vaporization of a saturated liquid to saturated vapor at constant pressure of 102.7 kPa and 506.8 kPa. Which case requires more energy? show all necessary calculations