A rectangular concrete beam 300 mm wide is subjected to a sagging moment of 20 kN-m and a torsional moment of 30 kN-m. Design a suitable depth for the beam and the required. longitudinal reinforcement Allowable stresses are: Ocb = 5 N/mm; Os = 140 N/mm and m = 19 The following criteria given in the code may be used for design: Equivalent bending moment Mel = M+MT Where M bending moment at the cross- 1+D/b section and M, = T 1.7 %3D Where T= Torsional moment, D= overall depth of beam and b = breadth of beam. If M, given by the above equation exceeds the numerical value of the moment M, longitudinal reinforcement shall be provided on the flexural compression face such that the beam can also withstand an equivalent moment Me2 =MT-M Being taken as acting in the opposite sense to the moment M.

A rectangular concrete beam 300 mm wide is subjected to a sagging moment of 20 kN-m and a torsional moment of 30 kN-m. Design a suitable depth for the beam and the required. longitudinal reinforcement Allowable stresses are: Ocb = 5 N/mm; Os = 140 N/mm and m = 19 The following criteria given in the code may be used for design: Equivalent bending moment Mel = M+MT Where M bending moment at the cross- 1+D/b section and M, = T 1.7 %3D Where T= Torsional moment, D= overall depth of beam and b = breadth of beam. If M, given by the above equation exceeds the numerical value of the moment M, longitudinal reinforcement shall be provided on the flexural compression face such that the beam can also withstand an equivalent moment Me2 =MT-M Being taken as acting in the opposite sense to the moment M.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From load analysis, the following are the factored design forces result: Mu = 440 KN-m, Vu = 280 KN. The beam has a width of 400 mm and a total depth of 500 mm. Use f’c = 20.7 MPa, fy for shear reinforcement is 275 MPa, fy for main bars is 415 MPa, concrete cover to the centroid of the bars both in tension and compression is 65 mm, steel ratio at balanced condition is 0.02, lateral ties are 12 mm diameter. Normal weight concrete. Calculate the required area of compression reinforcement in mm2 due to the factored moment, Mu. Express your answer in two decimal places.
SITUATION B: The beam is to carry an Ultimate Moment of 580 kN-m, geometrical property of the beam are the following: width of the beam = 350 mm, total height of %3D the beam = 670 mm , steel cover = 50mm. Use concrete strength f'c=21 MPa, steel %3D yield strength fy = 415 MPa and Ø = 0.877 %3D 4. What is the minimum number of 28-mm diameter reinforcing bars needed in the tension zone?
1. The strain profile of the section below with compression reinforcement was calculated with a computer program. All dimensions are to center of the reinforcements. Material properties: (a) (b) (c) Concrete, f'e = 4.0 ksi Steel, fy = 60.0 ksi Is the section tension controlled? What is the strength reduction factor (p)? Check if the forces in the section are in equilibrium. Do not correct them if they are not in equilibrium. What is the nominal moment resistance of the section? (4) #9- #5@4" (5) #11. (5) #11 -24"- SECTION 3" 3" 3" 48" 0.015 0.01 0.005 Strain diagram eps ecu epst 10.035 0.01 @lowest reinforcing steel Strain Profile 0 10 20 30 40 50 60 -0.005
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
A continuous concrete beam shown in the figure has a width of b= 300 mm, an effective depth of d= 560 mm, and an overall depth of h= 600 mm. Concrete compressive strength fIc=21.0 MPa and steel yield strength fy= 275 MPa. The beam carries a superimposed dead load at span AB of 7.5 kN/m and at span BC, CD of 4.5 kN/m. A live load at span AB of 12.5 kN /m and at span BC, CD of 10.5 kN/m. Determine the number, N, of 20 mm ∅ deformed steel bars at the following sections1) support A 2) Support B 3) Support C4) between AB 5) between BC
Problem The following are the dimensions of a concrete T-beam section Width of flange, bf = 600 mm Thickness of flange, tf = 80 mm Width of web, bw = 300 mm Effective depth, d = 500 mm The beam is reinforced with 3-32 mm diameter bars in tension and is carrying a moment of 100 kN.m. Find the total compressive force in the concrete. Use n = 9.
need help.
Given are the following: 300 Unit weight of concrete = 24 kN/m3 f'c = 28 Mpa fpe = 850 MPa fpu = 1350 MPa Aps = 750 mm? foy = 1280 MPa Beam is a simple span and have a length of 24m. Use bonded tendons as prestressed reinforcement. A. Determine the value of fps (MPa) B. Determine the nominal moment strength (kN-m) 750 850
I want to solve question 1040 and the question information from question number 1039
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)
*Subject: Reinforced prestressed concrete - Civil Engineering *Please refer for my attached formula or guidelines solve this problem A one-way both ends continuous slab is to support the moments tabulated. Consider L=5m, Fc’=21MPa and fy = 415 MPA. Dead load Moments: +42kN.m at midspan ; -67 kN.m at support Live load Moment: +40kN.m at midspan, -44kN.m at support. Determine the minimum thickness of the slab.