A rectangular boat with additional load at the center of 7200 kg is submerged in water by 1.8 m. The boat is 8 m long and 6 m wide and 2.4 m high. • Find the total draft after the 7200 kg is placed at the edge of the boat without causing it to sink. Assume water is fresh with density equal to 1000 kg/cu.m. • Determine the initial metacentric height. • Determine the final metacentric height. Determine the shifting of the center of buoyancy.

Q: I need to find distance between mass center and surface center points (vertically) of this…

A:

Q: Learning Goal: To be able to use the parallel-axis theorem to calculate the moment of inertia for an…

A:

Q: CHOSS Section 1 420 mm 490 mm

A:

Q: TOPIC: HYDROSTATIC FORCES ON CURVED SURFACES, ANALYSIS OF GRAVITY DAMS AND BUOYANCY PLEASE PROVIDE…

A: tuxgndnbbjhbdjsjjscdbjgyt

Q: 60cm Waw A 23cm 6- 16cm SG=08 20cm 20cm SG= 13.6 SG=136 Given heights: 60cm, 23cm, 16cm, h, 20cm, 20…

A:

Q: A triangle inscribed in a semi-cirlce with radius r shown below. Locate the centroid from point O.…

A: To find centroid

Q: to find the moment of inertia about the x' axis?

A:

Q: l answer.

A: Ixxtriangle=B×H312=110×100312IxxSemi circle=π8r4=π8364

Q: What is the difference between velocity pressure and velocity head?

A: Answer difference between velocity pressure and velocity head is following

Q: What will be the metacentric height of a rectangular block having dimension 6 × 3 × 1.5 m if the…

A: Given - Dimention of rectengular block = (6×3×1.5) m Submerged height = 0.8 m To find - The…

Q: Explain parallel axis theorem. Determine moment of inertia about both the axis for the profile shown…

A:

Q: 25 mm 50 mm 100 mm -75 mm- C 25 mm –75 mm- 25 mm 50 mm 100 mm 25 mm -X

A:

Q: Find the moment of inertia with respect to a) x-axis, b) y-axis of the area in the first quadrant…

A: Given : Curves : y2 = 4x and x = 1

Q: BONUS PROBLEM Set B: Given figure shown locate the centroidal x and y of the blue areas. Also,…

A:

Q: Determine the moment of inertia with respect to the illustrated A axis of the C 150 x 19 profile.…

A: Objective: To determine the moment of inertia with respect to the A-axis as shown in the given…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A: Given: Required  Moment of inertia about centroidal X and Y axes

Q: 15' 10' 10 kips 10° U 10 kips 10 a 20⁰ F 10' 10 kips 10 kips 10° Solve for the force in Member CD…

A: Given:Required:Force in member CD

Q: 2. Block A is being pushed up the side of a wall. Kinematics dictates that motion can only be in the…

A:

Q: y 20 80 20 20 60

A:

Q: 2. A cantilever beam is subjected to a uniformly distributed load of 10 kN/m applied over its entire…

A:

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A: Properties of W150x24,d = Total depth = 160 mmb = Width of flange = 102 mmA = Total Area = 3.06×103…

Q: Discuss the relationship between bending moment, shear force and deflection, please provide all the…

A: The relationship between bending moment, shear force, and deflection is fundamental to the study of…

Q: A vertical rectangular plate is submerged half in oil (SG = 0.71) and half in water such that its…

A:

Q: Please

A: As there are multiple questions posted, according to the guidelines, only the first three are being…

Q: Draw the shear and bending moment diagrams of the beam loaded as shown in the figures below. Round…

A: Answer  Let us first draw the free body diagram of forces acting on beam Resolve inclined forces…

Q: 1.Explain Lateral Stability, Longitudinal Stability and Directional Stability in your own words.

A: Brief Concept Introduction- Lateral, longitudinal, and directional stability are related to the…

Q: Moment of inertia about x-axis (bottom-most) . Centroidal moment of inertia about x-axis lote: Unit…

A:

Q: A snowball rolls off a barn roof that slopes downward at an angle of 40°. The edge of the roof is…

A:

Q: Locate the centroid with respect from x and y axis

A:

Q: Determine the location in inches of the centroid of the gray section below with respect to the…

A: Given Data: The figure is a combination of rectangles and triangles. The gray section is obtained by…

Q: ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS AND FBD LEGIBLY. NO…

A: To find components of reaction at point C,, D, E

Q: shear force and bending moment on skateboard: write : introduction

A: In a skateboard, the forces act in two different ways. These forces differ with respect to the…

Q: orce A=25 N A B=30 N

A: On the left side, tan(theta) = Perpendicular/base  tan(theta) = 7/4 = 1.75 angle theta = tan inverse…

Q: 3.52 At a certain time during a hurricane, the wind pressure acting on the wall of a high-rise…

A: Given data:

Q: FLUID MECHANICS if jockey weight is 50 g and it's displacement is 2 cm , what will be the…

A:

Q: cross section 2 . 42 mm 42 mm I 50 mm 50 mm 302 mm 392 mm

A: A section have been given and it has been asked to determine centroid, moment of inertia and section…

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.