T-7 A pump is used to circulate hot water in a home heating system. Water enters the well-insulated pump operating at steady state at arate of 0.42 gal/min. The inlet pressure and temperature are 14.7 lbf/in.², and 180°F, respectively; at the exit the pressure is 60 lbf/in.²The pump requires 1/25 hp of power input. Water can be modeled as an incompressible substance with constant density of 60.58lb/ft3 and constant specific heat of 1 Btu/lb-°R.Neglecting kinetic and potential energy effects, determine the temperature change, in °R, as the water flows through the pump.AT = 1°R

Write the given data. V˙=0.42 gal/minP1=14.7 lbf/in2T1=180 °FP2=60 lbf/in2Win˙=125 hpρ=60.58…

A pump is used to circulate hot water in a home heating system. Water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. The inlet pressure and temperature are 14.7 lbf/in.2, and 180°F, respectively; at the exit the pressure is 60 lbf/in.2 The pump requires 1/25 hp of power input. Water can be modeled as an incompressible substance with constant density of 60.58 Ib/ft² and constant specific heat of 1 Btu/lb - R Neglecting kinetic and potential energy effects, determine the temperature change, in °R, as the water flows through the pump. AT = 1 °R

A pump is used to circulate hot water in a home heating system. Water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. The inlet pressure and temperature are 14.7 lbf/in.2, and 180°F, respectively; at the exit the pressure is 60 lbf/in.2 The pump requires 1/25 hp of power input. Water can be modeled as an incompressible substance with constant density of 60.58 Ib/ft² and constant specific heat of 1 Btu/lb - R Neglecting kinetic and potential energy effects, determine the temperature change, in °R, as the water flows through the pump. AT = 1 °R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The ring at B is supported in equilibrium by spring AB, a cable running through the frictionless pulley at C, and cable BD. The pulley radius is 0.0150 m, and the unstretched length of spring AB is 0.21 m. If F₁ = 390 N and F₂ = 170 N at 0=38 degrees, determine the spring constant & and the force exerted on the ring by cable BD expressed in Cartesian components. F₁ a b k C d values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable value 0.300 m 0.0900 m 0.150 m 0.0600 m FBD= C Note the figure may not be to scale. D Submit Question N/m B i+ A www. F2 3) N
The force from the cable AB attached to the screw eye at A is - {450 - i – 150 -j - 500 - k N. If the length of the cable is L= 12 m, then what are the values for x, y, and z? 202 Cahy Zupke The value of = m The value of y = m The value of 2 =
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions l1 = 0,31 m ja l2 = 0,23 m Determine the support force on the rear tire.
The 10 lb lamp is suspended from two springs, each having an unstretched length of 4 ft and stiffness of k=5 lb/ft. Find the angle 0 for equilibrium. 4 ft k=5 lb/ft -4 ft- wwwww HIN k=5 lb/ft
HW Problem Determine the components of F1 and F2 in x-y and x'-y' systems F1 = 500 lb 25° 45° 30° F2= 750 lb
! draw the free body diagram abd equations of motion.
Determine the stretch in each spring for equilbrium of the 2-kg block. The springs are shown in the equilibrium position. a= 2.5 m b=4.6m c=2.6m KAB=35 N/m KAC=25 N/m KAD=36 N/m с a wwwwww. KAC KAD b KAB wwwwwww B
Q 3
If the weight of the box its 10 determine the cable tensions TAB,TAC, TAD
Determine the maximum weight of the crate so that the tension developed in any cable does not exceed 410 lb. TA In -20 20 20 # Add your answer 20
Based on the figure If spring A is compressed (L / 8) Which shape is correct? 1 or 2 ?
8 and 9