A pump is drawing water from reservoir A to the system shown. If the velocity at point D is 2 m/s, determine the power needed in the pump in kilowatts if friction factor for all pipes is 0.017. (A) 663.49 KW B 494.96 KW 572.03 KW D No Answer among the choices E 724.83 KW

A pump is drawing water from reservoir A to the system shown. If the velocity at point D is 2 m/s, determine the power needed in the pump in kilowatts if friction factor for all pipes is 0.017. (A) 663.49 KW B 494.96 KW 572.03 KW D No Answer among the choices E 724.83 KW

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q3/ The horizontal pump in Fig. below discharges 20°C water at 57 m/h. Neglecting losses, what power…

Q: A large tank open to the atmosphere is filled with water to a height of 9.3 m from the outlet tap. A…

A: Discharge through the mouth piece= Q=Cd a2gH Velocity = Q/a= Cd2gH= 0.7072*9.81*9.3= 9.55 m/s So the…

Q: A pump dráws 24 litérs per second of water fr reservoir C and lifts it to reservoir D as shown The…

A: Given- Discharge (Q)=24 l/secDischarge (Q)=0.024 m3/sec

Q: Q3. A pump is required to pump water from a large reservoir to the water tower located 20 m above…

A: a) The expression for energy between velocity 1 and 2 is given as P1γ+V122g+z1+HP=P2γ+V222g+z2…

Q: A rectangular channel has a width b = 8 m. The critical specific energy in the channel (Ed = 2.6 m.…

A: Explained below...

Q: 2.) Given: Q = 438 lit/sec; pressure at 1 = 72KPA; pressure at 2 = -40.2KPA Req'd: horsepower input…

Q: A pump pumps water from one tank (open to atmosphere) to another tank (open to atmosphere) at a…

Q: Find the power loss (in kW) when a fluid of dynamic viscosity = 1.2 Pa.s and p = 1150 kg/m3 flows at…

Q: The efficiency (ŋ) of pump and turbine are given as ŋ = 80% and N = 70%, respectively. The national…

Q: The two-lobe rotary pump moves 0.145 gal of a coal slurry in each lobe volume Vlobe. Suppose the…

A: Given data:

Q: The stream channel and floodplain shown has overbank Manning's n of O.10 and channel n = 0.030. The…

A: We are required to calculate the energy coefficient

Q: The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce…

Q: A sluice gate, as shown in Figure Q1, is used to control the upstream water level in a 4 m wide…

Q: A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle B2 is…

A: ANSWER: Option (B)-22.1 is Correct

Q: Water flows from reservoir A through a turbine and discharges to B through a 24 in diameter pipe.…

Q: Q4: A turbine is located in pipe No.2, shown in figure (4). If the turbine efficiency is (90%), what…

Q: 18: A pelton wheel has a mean bucket speed of 10 m/sec with a jet of water flowing at the rate of…

Q: defeat Water is pumped from a lake to a storage tank 80 m above at a rate of 0.005 m³/s. If the GL…

Q: 5. The horizontal pump in the Figure discharges 30°C water at 40 m'/h. Neglecting losses, what power…

Q: salá* The pump in figure delivers 0.05 m3/s water up to head= 200 m, find the ?required power the…

A: To find out the required power the pump must be deliver to water.

Q: Example. A pump lifts water from a large tank at a rate of 30 Ls. If the input power is 10 kW and…

A: Q=30lpsP=10kWη=40%so,η=output input×1000.4=output 10×100output=4kW

Q: 300 mm d 300 mm d Problem 4.113 4.113. This turbine develops 75 kw when the flowrate is 0.6 m'/s,…

A: Bernoulli’s equation is generally applied between any two points, to find variables like pressure,…

Q: The following applies the figure (6): (PA= 207kPa.), (P=689.44kPa.). (Q= 0.14 m'/s), elevation of…

Q: An elevated water tank consists of an upper cylindrical part (4.88 m in diamwter and 6.10 m high)…

Q: Q3. A pump is required to pump water from a large reservoir to the water tower located 20 m above…

A: Given : z1 = 0 z2 = 20 P1 = 0 P2 = 0 hL = 0 D = 30 mm Q = 0.03 m3/s ρ=1000 kg/m3 V1 = 0 A)…

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of shaft…

A: Given Head = 45 m Flow rate = 0.03 m3/s Shaft power = 20 kW

Q: The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce…

Q: What is the required shaft power (kW) that must be supplied to pump water at flow rate 0.010 m /s…

A: Given Q = 0.01 m3/s z1 = 10 m z2 = 45 m f = 0.04 L = 100 m D = 50 mm Efficiency of pump = 44%

Q: Situation XII: Water is being raised from reservoir A to reservoir B using pump as shown. The…

Q: 9. Water is flowing through a pipe of 3.8 cm diameter under a pressure of 20 N/cm2 (gauge) and with…

Q: he power input of the pump is 10 kW and the friction head loss between A and B is 1.25 n. If the…

A: DA=0.5m DB=0.25m ZA=0m ZB=2m

Q: The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce…

Q: Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoir at elevation 70 m.…

Q: A pump is rated with 80% efficiency and requires 4hp of power. The power output results to a…

A: Efficiency of the pump = QHρ367 P2 ρ=1000 kg/m3 P2= 2.9828 KW Velocity = 5ft/s=1.524 m/s Average dia…

Q: The water in an aquarium will be drained for cleaning. A flexible tube (D = 4mm) will be used to…

Q: Can you also draw the figure A pump delivers water from a lower to a higher reservoir. The…

Q: The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce…

A: GIVEN : The pump-turbine system draws water from the upper reservoir in the daytime to produce…

Q: shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water…

Q: Calculate the minimum power of the pump which will send the jet of water over the wall shown in…

Q: 5. The horizontal pump in the Figure discharges 10°C water at 35 m/h. Neglecting losses, what power…

A: Given data: Discharge,Q=35 m^3/hr Inlet Pressure,Pin=210KPa Outlet Pressure,Pout=440KPa Inlet…

Q: A pump helps bring oil (SG 0.8) to reservoir D from reservoir A at 235 liters per %3D second. The…

Q: The water tank is connected with a pipe ( Diameter= 5-cm) as shown below. Find the horse power of a…

A: The pump is the device that helps to transmit the water from lower level to higher or to another…

Q: Water is at 20°C is pumped from a lower reservoir to a higher reservoir by a pump at a rate of 10…

A: To Determine the friction head loss (m)?

Q: A tank has an elevation of 5m with an installed square pipe powered by a pump with an input of 300kW…

A: Q = 145L/s = 0.145m3/s A = 0.04 m2 or, 3.14*D2 /4 = 0.04 or, D = 0.2257m V (velocity) = Q/A =…

Q: A dam gate in the figure shown admits water toa horizontal canal. Considering the pressure…

Q: compute the shaft diameter. What power can be transmitted by the shaft at 20

Q: How long does it take to raise the water surface in the figure shown by 1.5 m? The left-hand surface…

Q: A pump helps bring oil (SG = 0.8) to reservoir D from reservoir A at 235 liters per %3D second. The…

A: step1-

Q: 2. Determine the power delivered to the turbine if the water exits the 400-mm-diameter pipe at 8…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

ELEV. = 25m
ELEV. = 15m
L = 1829m
D = 508mm
L = 1220m
D = 406mm
E
4
ELEV. = 10m
ELEV. F 5m
L = 2440m
1
A
P
L = 1110m
D = 915mm
D = 610mm
3.
B.

A pump is drawing water from reservoir A to the system shown. If the velocity at point D is 2 m/s, determine the power
needed in the pump in kilowatts if friction factor for all pipes is 0.017.
A 663.49 KW
B) 494.96 KW
C) 572.03 KW
D) No Answer among the choices
E) 724.83 KW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

d?y dy 7y = 6e2x, dx2
er Engineers: El X dXGr5FXCENdllpHQzzLvM_oCLpBbBinmD4RvO_nqWeFros9A/formResponse Solve for the Center of Gravity of the figure below. 4 cm 1 cm 4 cm 2 cm 1 cm 1.5 cm 1cm From the Origin, X = 1 cm 1.5 cm 2 cm 2.5 cm Other: Clear selection 20
Y Given: X x1 x2 . x1 = 15.35 mm • x2 = 16.74 mm . x3 = 16.10 mm .y1 = 19.32 mm y2 = 20.55 mm y3 = 16.37 mm mie x3 sterren T y3 y2 y1 Find x & y centroid
find the foree in members DF, DG , EG. B 20N lom H E ION 15N 10N lom lom 10m
V=38 h1=96 h2=12 D1=6 D2=3 angle = 20 degree
1025ft2 * 8ft = Convert answer to m3
3. Submissions must be in pai or jpeg PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B. Determine the reactions at these supports. A6 On peg wil 800 KN EX tim Im - Im - Iskwilm 300 *** 199 201 4m THE
136 N is the asnwer in the book
Draw the FBD of member ABC 160 mm 90 mm 240 N A 180 mm В M D 320 mm 125 mm 300 mm
4) Find the most economical wide flange section for an A992 steel beam (E = 29 x 10³ ksi) using LRFD which spans 45 ft. with a dead load of 50 lb/ft² and a live load of 95 lb/ft² if the beams are spaced 12 ft apart and full lateral bracing is provided. Determine the total maximum deflection. (Because the beam is fully braced, you should utilize a reference table with wide flanges in descending order of Z as found in the note set.) Additional wide flange properties which the text does not show text is provided on the following pages.
I5KN Draw and label the V and M diagrams. Fill in the blanks. Find M- max and the equations for q, V, and M in the region 3
The reduced form of 3y (0) – 21y (4) + 5y''– 10y"+42y'- 8y+ 5=0 js: A (3D5- 21D4+5D³ – 10D²+42D – 8) y=0 B (3D5- 21D4- 5D³+ 10D²+42D – 8) y= - 5 (3D5- 21D4+5D³ – 10D² – 42D +8) y= - 5 (3D5- 21D4- 5D³ – 10D²+42D + 8) y=0