A pressure-fed bearing has a joumal diameter of 55.00 mm wvith a unilateral tolerance of -0.05 mm The bushing bore diameter is 50.084 mm with a unilateral tolerance of 0.10 mm. The length of the bushmg is 55 mm. Its central annular groove is 5 mm wide and is fed by SAE 30 oil is 55°C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 10 kN. The sump ca dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the minimum film thíckness and average temperature. Given the film temperature is 85°C Attach File Browse My Computer

A pressure-fed bearing has a joumal diameter of 55.00 mm wvith a unilateral tolerance of -0.05 mm The bushing bore diameter is 50.084 mm with a unilateral tolerance of 0.10 mm. The length of the bushmg is 55 mm. Its central annular groove is 5 mm wide and is fed by SAE 30 oil is 55°C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 10 kN. The sump ca dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the minimum film thíckness and average temperature. Given the film temperature is 85°C Attach File Browse My Computer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please provide the correct answer choice
18 The power output of a six cylinder four-stroke engine is absorbed by a water brake for which the law is WN/20000 where the brake load, W is in Newton and the speed, N is in rpm. The air consumption is measured by an air box with sharp edged orifice system. The following readings are obtained. Orifice diameter 30 mm Bore 100 mm Stroke 120 mm Brake load 560 N %3D C/H ratio by mass Coefficient of discharge Ambient pressure Pressure drop across orifice Time taken for 100 cc of fuel consumption Ambient temperature Fuel density 83/17 0.6 %3D 1 bar 14.5 cm of Hg 20 s 27 °C 831 kg/m³ Calculate (i) the brake power (ii) the torque (iii) the brake specific fuel consumption (iv) the percentage of excess air and (v) the volumetric efficiency
Take your time for solving problem. Please solve the Below problem using 'Design data book'. And while solving problem add some table or figure reference number before taking each reference value. If answer is right then I will give you upvote/like.
Q108 The fallowing data refers to a test ona single cylinder four stroke oil engine Cylinder bore 220mm; stroke 360mm; area of indicator diagram 360mm length af diagram 40mm; indicator Spring rating =1.25 mm/bar; Speed 300 rev/min brake load 441-3N at o.9m radius; fuel consumption 3.8 Kg/hr} Calorific Value of fuel 43124 kj/kg ; Cooling water flow 3.8kg/hrjrise intemperature of coaling water 48K;and specific heat capacity of water 4.1868 Kj|Kg.K 340d.13biliN Calculate: @ the mechanical efficiency the indicated thermal efficiencyui a The heat balance sheet expressed as ki/min andas percentage of the heat supplied to the engine.
Q: A multi disc clutch is used to transmit to 10 kW power at 900 rpm. If the external diameter of friction lining is 1.25 times the internal diameter, find the required dimensions of the friction lining and the axial force exerted by the oil chamber pressurized to engaged the disks a with disks b. The pressure between disks is limited to 0.085 N/mm?. Assume average service condition. The coefficient of friction may be taken as 0.3. Disks a Disks b Seals Oil chamber (pressurized to engage clutch) Piston Bushing Oil passage Output Key Key Input Oil passage Page 1 of 1
A CONE CLUTCH WITH CONE ANGL€ 20 IS TO TRANSMIT 7.5KW AT 750 8 P.m. THE NORMAL IN TENSITY OR PRESSURE BETWEEN THE CONTACT CACES IS NOT T O EXCEED 0-12N Imm? THE COEFEICIENT OF FRICTI(ON IS 0.2.1E FACE WID TH IS TH OF MEAN DIAMETER, FIND a) THE mAIN DIMENSIONS OF CLUTH AND (b) AXIAL FORCE REQUIRED whILE RUNNING
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply (m; ) is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque (4) being correspondingly adjusted. The brake power (bp) measurements are the following: With all cylinders firing With cylinder No. 1 cut off With cylinder No. 2 cut off With cylinder No. 3 cut off With cylinder No. 2 cut off = 9.1 kW 12.5 kW 9 kW 9.15 kW 9.2 kW The lower calorific (or heating value, LCV) of the fuel is 44100 kJ/kg. The clearance volume (Va) of one cylinder 70.0x10³ mm³. Determine: (a) Indicated power (ip) of the engine under these conditions. (b) The indicated thermal efficiency (Nind, th). (c) The relative efficiency (7el) of this engine.
A light duty sleeve bearing operates in still air at air temperature of 70 °F and sustains a load of 350 lbs. A shaft rotates at 600 rpm. The coefficient of friction is 0.015 between shaft and bearing. The shaft diameter is 1.75 in. and the bearing length is 2.50 in. Find the probable operating temperature of the bearing. A. 143.45 deg F C. 134.54 deg. F D. 125.74 deg F B. 171.7 deg. F
Design a single row deep groove ball bearing with basic dynamic load rating of 25.5 KN to be used in a turbine to carry a radial load of 1607 N. The expected life of the bearing is 5226 hours at 523 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in N
I need answer in handwritten
A pressure-fed bearing has a journal diameter of 63.00 mm with a unilateral tolerance of -0.05 mm. The bushing bore diameter is 63 084 mm with a unilateral tolerance of 0.010 mm. The length of the bushıng is 58.00 mm. Its central annular groove is 8.00 mm wide and is fed by SAE 30 oil is 55°C at 195 kPa supply gauge presaure. The journal speed is 2880 revimin carrying a load of 20 kN. The sump can dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the average temperature Given the film temperature is 95°C
i need the answer quickly