A portion of the floor plan of a building is shown in Fig. P-543. The total loading (including live and dead loads) in each bay is as shown. Select the lightest suitable W shape beams if the allowable flexural stress is 120 MPa. Wall 2.5 m -2.5 m- t-2.5 m- -2.5 m- - -2.5 m- 2.5 m 15 kN/m2 15 kN/m2 9 kN/m2 9 kN/m2 15 kN/m2 15 kN/m2 7 m (В-3) (B-3) (B-2) (B-1) (B-2) (G-1) Stair well 2 m Wall

A portion of the floor plan of a building is shown in Fig. P-543. The total loading (including live and dead loads) in each bay is as shown. Select the lightest suitable W shape beams if the allowable flexural stress is 120 MPa. Wall 2.5 m -2.5 m- t-2.5 m- -2.5 m- - -2.5 m- 2.5 m 15 kN/m2 15 kN/m2 9 kN/m2 9 kN/m2 15 kN/m2 15 kN/m2 7 m (В-3) (B-3) (B-2) (B-1) (B-2) (G-1) Stair well 2 m Wall

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1- The floor beam in Fig. below supports nonstructural elements not likely to be damaged by large deflections. If the service dead load equals 21 kN/m and the service live load equals 12 kN/m, does the 450 mm beam satisfy ACI Code requirements for allowable 400 mm deflections? f = 25 MPa, fy= 400 MPa. SØ25 mm %3D 75 mm
Our University wants to construct a signal post near the entrance, for which they are in need of a horizontal structural element with one end fixed and other end is free. That is to be made up of flexible composite material. The maximum allowable load at free end is 900 kN. The length of the horizontal structural element is 2.2 m. The cross section of the beam is a hollow circular section. Outer diameter 200 mm with wall thickness of 20 mm. Find the deflection at the free end and maximum slope in beam by neglecting self-weight of the diving board. Take Young's Modulus as 170 GPa.
1. Three concentrated loads of 50kN, 30KN and 60 kN are loaded on a 14-meter-span fully-restrained beam and each applied at 7 m, 9m and 11 m from the left support respectively. Which of the following most nearly gives the elastic section modulus of the beam (in mm³) if the shape factor is 1.4 and the yield stress is 240 MPa. a.443.667 b. 546.778 c. 488.775 d. 505.952 e. 521.345 2. A W 14 x 68 having the following properties:Prop. of W 14 x 68d = 356.62 mm Sx = 1688 x 10³ mm³ Cb = 1.14bf = 254.89 mm Zx = 1885 x 10³ mm³ Lp = 2.65 mtf = 18.29 mm E = 200000 MPa Lr= 8.05 mFy = 345 MPa Elastic buckling stress: Fcr = 420 MPa Which of the ff. most nearly gives the flexural strength of the beam if the beam has an unbraced length of 12 m. a. 450 b. 709 c. 638 d. 486 e. 585 Which of the ff. most nearly gives the flexural strength of the beam if the beam has an unbraced length of 6 m. a. 585 b. 709 c. 638 d. 450 e. 486
b) The floor system shown is subjected to a total uniform distributed load of 20 kN/m². Sketch the loading that acts along the members and CDE. 2 m E 3 m F G H 4 m 3 m
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Thickness, tf=9mm Flange Width, B=112.5 mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear 1. Determine the location of centroid, ȳ, from top of the beam in mm
Given. A two-story OCBF shown in Fig. 3.40c that forms part of the building frame system in SDC E. The axial loads on the ground floor brace B1 are as follows: Dead load D= 30 kips Live load L= 15 kips Seismic force QE = ±80 kips Snow load S= 0 kips Hydrostatic load H = 0 The redundancy coefficient p = 1.1. Mapped two-second såpectral acceleration, Sps = 0.826 g. Required. Determine a pipe section for brace B1, ASTM A53 Grade B steel; F, = 35 ksi, F = 60 ksi 16 ft 16 ft Figure -15 ft B2 B1 -- -15 ft B2 B1 Ordinary concentric brace frame (OCBF) example.
A reinforced concrete beam of rectangular cross-section of breadth 230 mm and effective depth 400 mm is subjected to a maximum factored shear force of 120 kN. The grades of concrete, main steel and stirrup steel are M-20, Fe-415 and Fe-250 respectively. For the area of main steel provided, the design shear strength tc as per IS : 456-2000 is 0.48 N/mm2. The beam is designed for collapse limit state.
A post-tensioned bonded concrete beam has a prestress of 1560 kN in the steel immediately after prestressing which eventually reduces to 1330 kN. The beam carries two live loads of 45 kN each in addition to its own weight of 4.40 kN/m. Compute the extreme fiber stresses at mid-span:a) under the initial condition with full prestress and no live load; b) under final condition after all the losses have taken place and with full live load.
4. A timber beam triangular in section of base 100 mm and altitude 200 mm carries the loading as shown. If the maximum flexural stress is 15 MPa, for what value of w will the shear be zero under P? What is the value of P? 3 m. 200 min B 100 mm
Problem 1 The members of the truss shown below are of plain concrete. The compressive cylinder strength of concrete is 30 MPa. Determine whether the structure can carry the applied load. 31 KN 24 KN D 120x120mm 40x40mm 40x40mm 120x120mm 300 mm 40x40mm 400 mm
. Determine the safe uniform load that the 200 mm x 400 mm simple beam could carry over a length of 5.0 meters if the allowable flexural stress is 14.30 MPa and the shear stress is 0.82 MPa. 10 KN W 400 mm puding 2.50 m 2.50 m 200 mm
The W610 x 82 beam shown above has a Young’s modulus of ? = 200 GPa, an allowable bending stress of ?????? = 300 MPa and an allowable shear stress of ?????? = 150 MPa.a) Draw the SFD and BMD of the beam and indicate ???? and ????.b) Determine if the beam is sufficiently strong to support the applied loads.c) Assuming that the beam is sufficient, what is the vertical deflection and slope at the free end?