A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 cm diameter. A lubricating oil which fills the space between them has viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. 14 cm VF- 0.86 Kg,t

A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 cm diameter. A lubricating oil which fills the space between them has viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. 14 cm VF- 0.86 Kg,t

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the moment of inertia about its base
Q2// Consider a special ball made of steel (p- 5000 kg/m', Cp- 300 J/kg. k, A= 60 m²). The initial temperature of the ball is 300 K. It is immersed in a large oil tank at 400 K. The convective heat transfer coefficient, h at the sphere surface is 3000 W/m³. k. Assume that there is no radial temperature gradient inside the ball. Use Euler's method to find the temperature of the sphere at t = 15 sec after it was immersed in the oil tank. Use a step size of h= 5 sec. The energy balance equation of the ball is given by the following equation: dT pCp -=-hA(T-T₂) dt
Consider the tank shown. Which of the following pressure relations is correct? Air Air 2 ft 3 ft Air 4 ft Water Select one: О а. Рс РD O d. Pp > PA
Jet. of liquid (14 mm diameter) ejections vertically into the atmosphere. The pressure inside the jet (due to surface tension) will be slightly higher than the atmospheric pressure. Determine the difference in pressure (in Pascal). (take o 8.35*10-2 N/m for liquid)
Solve all questions.
It’s required to determine the height (H) when the flow is 120 L/s ؟
%07 3º,l|Asiacell نقطتان )2( * :Q6 The cylinder shown in the figure extends 8 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil (s.g. = 0.85 ) 4 ft 50°
A steam function is given by: 4 = 2x²y + (x + 1)y² The flow rate across a line joining points A (3, 0) and B (0, 2) is
Question - Civil hydraulics The diameter of the U-tube is one-tenth the diameter of the enlarged ends, and a double column enlarged ends manometer is used to measure a minor pressure differential between two points of a system transporting air under pressure. Water is employed as the heavy liquid, and oil with a relative density of 0-82 is used as the lighter liquid in both limbs. Calculate the difference in pressure in millimetres of water for a manometer displacement of 50 mm, presuming the lighter liquid's surfaces stay in the larger ends. If carbon tetrachloride, which has a relative density of 1.6, were used in place of water but the pressure conditions remained the same, what would the manometer read?
A flocculate is designed to achieve a velocity gradient of 50 s with a volume of 3000 m' .the viscosity of the water is 1.1x10 Pa-sec. The coefficient of drag paddle is 1.8 and paddle tip velocity is 0.8 m/sec. The relative velocity of the paddle is with respect to water is 70% of paddle tip velocity. The mass density of water is 1002 kg/m. Calculate the power required for paddles and total area of the paddle blades. a) 7.57 kW and 45.98 m² b) 9.12 kW and 60.53 m² c) 8.25 kW and 52.10 m² d) 6.38 kW and 39.59 m?
None
0.0 3,MM, distance from P