A petrol engine has a cylinder diameter and stroke of 120mm and 245 mm respectively. The clearance volume is 0.00029 m3. Find the total volume of the cylinder in m3. The total volume in m3

Q: What is the indicated horsepower of a single cylinder four-stroke gasoline engine if the engine…

A:

Q: Engr. Mercado wishes to replace a solid transmission shaft 4.2 inches with a hollow shaft of same…

A:

Q: The gear 'A' and gear B' are tried to transmit power from one shaft to another shaft. The gear 'A'…

A: Let us discuss about power transmission between shaft A and shaft B. Given data, Gear A, Tooth space…

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A: Find , Clearance volume  Swept volume ,

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: Compute the displacement done in object so that work done is said to be 124.55 J If force applied is…

A:

Q: A petrol engine has a cylinder diameter and stroke of 120mm and 210 mm respectively. The clearance…

A: Given data, D = 120 mm = 0.12 m L = 210 mm = 0.21 m Vc = 0.00029 m3 Find: V = ?

Q: In a hydraulic press the diameter of the plunger is 50 mm . Find the diameter of the hydraulic press…

A: Diameter of the plunger, d1=50 mm= 0.050 m Weight at the plunger, W1=450 N Force at the Hydraulic…

Q: The effective diameter of the cylinder is 400 mm. the maximum pressure of steam acting on the…

A:

Q: A duct in which methyl alcohol at 25 degrees celcius flows at the rate of the 3000 L/min. Compute…

A: Given:  flor rate of methyl alcoholQ=3000 Lmin=3000100060 m3sec=0.05 m3sec we know that flow…

Q: Engine has a capacity of 20 milliliters per cylinder and the length of the axle arm is 5 cm Find the…

A:

Q: A circular shaft with diameter 50mm and its length is 850mm long and is made of steel,The shaft is…

A:

Q: Given is the following stress tensor (values in MPa): 48 ay = ( ) Oij -4 62 culate the magnitudes of…

A:

Q: elect the diameter of the cylinder to be used from L=150mm, if it is required to apply a force of…

A: Given   Pressure, P = 80 psi                     = 551.58 kPa       Mass, m = 350 kg Find…

Q: calculate the hydraulic diameter of a two long flat plates with the measurement of 5 inches distance…

A:

Q: a)The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is…

A: Given data: -  The number of cylinders is n = 6. The bore of each cylinder is D = 45 mm. The stroke…

Q: Express shaft in series and set some example in prismatic condition and pure torsion condition.

A: Below is the solution of the above problem with all the requirements as mentioned by you.

Q: The horsepower developed at the end of the crankshaft of a 4-stroke, 4 -cylinder internal combustion…

A:

Q: An aluminum cube with an edge of 5 cm is resting on the ground on one of its faces. calculate the…

A: Given data  s= 5 cm = 0.05 m  d= 2700 kg/m³  Note: diagram is not necessary for the understanding…

Q: The spring used in the shock absorber has a spring index of 13. Calculate the outer diameter of the…

A: Springs are used in the shock absorbers. When the load is applied on the spring, it compresses and…

Q: If pitch circle radius of a sprocket is 14.8 cm and pitch of the chain which can engage with this…

A: Pitch is the distance measured along the circumference of the pitch circle from a point on the tooth…

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

A:

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: The diameter of shaft  is 45mm. Compare the shear stress in the key to the torque in the shaft.…

A:

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: Given: The center distance between shafts is 1.67 ft. The speed of the input shaft is 350 rpm. The…

Q: the system is used to lift à mass of A compound lever as shown below. Find the effort 800kg. (10)…

A: As per policy experts are allowed to answer only one question (first one), for the second one please…

Q: Convert 589 mm to m.

A: Given Data : Length (L)=589 mm

Q: 3. Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by an open belt.…

A: In the above question the RPM of the driving shaft is given to be 150RPM and let us denote the…

Q: What is the diameter of line shaft that transmit 180 kW at 25 rps?

A:

Q: A transmission shaft used to transmit power of 55 kW. During transmission shaft is subjected to a 30…

A: Given data: The power transmitted by the shaft is P = 55 kW. The torque acting on the shaft is T =…

Q: gas is under pressure of 21.868 bar absolute at 40°C. Compute the gas constant R if it has a unit…

A: Given Data P= 21.868 bar T=40°C Unit weight= 362 N/m3

Q: Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside…

A:

Q: Determine the cylinder displacement and engine displacement of an engine having six cylinders with a…

A: Number of cylinders = 6  Bore = 400 mm  Stroke = 160 mm

Q: Determine the minimum acceptable diameter of the shaft using the DE- Morrow criterion. Determine the…

A:

Q: A petrol engine has a cylinder diameter and stroke of 120mm and 235 mm respectively. The clearance…

A: Given: Diameter of cylinder , D = 120 mm = 0.12 m Length of stroke , L = 235 mm = 0.235 m  Clearance…

Q: The cylinder of a four-stroke diesel engine has the following specifications: Brake power = 3.75 kW…

A: To find: The bore and length of the cylinder. Given: The brake power is BP=3.75 kW. The speed is…

Q: Question 4 )Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: At what depth below the surface of the oil, relative density 0.83 will produce a pressure of 100…

A: Fluid Mechanics

Q: The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke each piston is 125…

A: given:diameter d=45mml=125mmCR=8.75

Q: Find the angle at which the compound rest is to be swivelled or set with the following data: a)…

A: Answer: The angle at which compound rest is to be swivelled is 7.125°.

Q: v = 10 m/s D 300 mm 300 mm

A:

Q: Head: Flexible, constant spring of intensity m / N 350 of length 40 cm affected It has a power of N…

A: Given data: The spring constant is K=350 N/m The power of force is F=20 N The length of the spring…

Q: an air cylinder has a bore of 25 mm and is operated with shop air at a pressure of 6.327 kg/cm2 .…

A: Given data: d=25 mmp=6.327 kg/cm2 Need to determine the push force exerted by the piston rod.

Q: Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pr

A: Given Data⇒ Cast iron cylinder Diameter of cylinder(d)=250 mm Pressure (P)=0.7 Nmm2 Maximum tensile…

Q: 120 kN 50 kN/m 4 m 1m 8 m 2 m

A: Calculate the support reaction as follows, RA+RB=120+50×5RA+RB=370 kN     .......... (1)Taking…

Q: . Determine the displacement of an eight-cylinder engine having a bore of 3.25 n and a stroke of 3…

A: given data bore diameter = 3.25 in  stroke length = 3in  number of cylinders =8 to determine  the…

Q: A belt is to transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at…

A: .Given:  power transmitted→P=50 KW=50000 W Diameter of the driving sheave→D1=10…

Q: A machine has to carry out punching operation at the rate of 10 holes per minute. It does 6 kN-m of…

A: Given: Rate of Punching = 10 hole/ min Work done during punching = 6 KM.m/mm2 Diameter of Hole= 25…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.