A package of frozen fish sticks have different instructions when they are heated up on the stove as compared to using the oven. Stove: Heat over medium flame for 2 minutes. Then flip the fish sticks (turn them over) and heat them for another two minutes. Oven: Preheat the oven to 375 F. Put them on a metal baking sheet for 15 minutes. a. Explain why the instructions have you flip the fish sticks over when you're heating them with the stove, but not with the oven. b. If you follow the oven instructions, the side of the fish sticks touching the metal baking sheet will cook more than the top side of the fish sticks. Explain why.

A package of frozen fish sticks have different instructions when they are heated up on the stove as compared to using the oven. Stove: Heat over medium flame for 2 minutes. Then flip the fish sticks (turn them over) and heat them for another two minutes. Oven: Preheat the oven to 375 F. Put them on a metal baking sheet for 15 minutes. a. Explain why the instructions have you flip the fish sticks over when you're heating them with the stove, but not with the oven. b. If you follow the oven instructions, the side of the fish sticks touching the metal baking sheet will cook more than the top side of the fish sticks. Explain why.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HOTSPOT ANSWER Question 2 Which hotspot on the lever below acts as the Effort?
hi can you please answer question 9? in a step by step way! thank you
A technician uses these items in fixing a hot water heating system:Find the total cost of the items used.Note: Use this information and diagram for problems 21 and 22. TheR value of a substance gives the resistance of a substance to heatflow. The larger the R value, the more resistant the substance is toheat flow and heat loss. The total resistance is the sum of each substance’s resistance.
Problem- Cargo ships can cause a lot of air pollution.Solution- to use nuclear powered ships since they hold a lot of energy and can travel for long distances. How it will work is that it will need a nuclear reactor at the bottom of the boat to heat up the water and then turn it to electricity to power the boat. The boat will be made out of graphene which is a tough material to avoid any leaks in the boat. It will also contain many control rods because nuclear power is so powerful that it can create to much energy to handle. With control rods, you can slow down this process and keep it in a controlled manner. Since cargo ships are already is the ocean, there will be no need for any extra materials to make it work. -Do you think this will work? Why/Why not? -What do you think is wrong with it/ How can this be improved? Please send this to someone else I need to record 50 responses for a science project. Thank you!
Task 1: Your first customer asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report which includes the following steps: Describe with the aid of diagrams the operational sequence of four stroke spark ignition and four stroke compression ignition engines. Review the efficiency of ideal heat engines operating on the Otto and Diesel cycles by explaining and generating plot(s) for thermal efficiency, 7 vs compression ratio and cut-off ratio.
Question 5.20 only!!!
dont type solution steps
4. Please only use 3 sig figs to answer.
hints: The ﬂask will be filled with water (at a constant rate of 500 gallons per minute). It will take me exactly 10 minutes to escape from the chains. The diameter of the tank at 1 foot intervals. I am 5 feet 9 inches tall, and I'm pretty skinny so that you can ignore both my volume and the volume of the stool in your analysis. A gallon is equal to 0.13368 cubic feet. You can think of the volume and the height of the water as functions of time. You can easily find an expression for V (t), and then use your expression for volume in terms of height to solve for h(t). after 10 minutes amount of water in the tank=66.84 ft3 t=69.3 minutes h(t)=e66.84t/100pi -1 h(10)=e66.84(10)/100pi -1=7.39 ft Height of stool=1.64 ft Height of water in the tank=7.39 ft Questions: show work How fast is the water rising? I would like to know how long I will have to hold my breath during the last part of the stunt.
Ventilation: The plant must have adequate ventilation to prevent the buildup of oxygen gas, which can be flammable and cause potential hazards. Electrical equipment: All electrical equipment used in the plant must be designed for use in a hazardous environment. Structural requirements: The building must be designed to withstand the weight and pressure of the refrigeration and cryogenic systems, as well as the potential stresses caused by temperature fluctuations. Please elaborate it well, this is an indoor consideration when designing cryogenic plant. you can add more.
Project 2: In company that designs road cars and heavy trucks, it important to make the proper selection of the engines. Your part as a system energy engineer is to make a proper selection between an engine operates on Otto cycle/gasoline engine or Diesel cycle/diesel engine. Your head of department asked you to provide a detailed technical report that shows your selection for engine to be used with heavy truck vehicle. This is best achieved by performing the following tasks: Section.1: 1. Which engine does operate at lower ??? and has higher air-fuel mass ratio? 2. Which engine does burn fuel more completely? 3. Which engine has lower fuel cost? 4. Explain what compression ratio for Otto and Diesel cycles means 5. Explain what cut-off ratio for Diesel cycles means 6. Explain the limitations of SI engines in terms of their ability to operate at much higher compression ratios. What is this limitation called? 7. Provide general plot(s) for thermal efficiency, ? vs compression ratio, r…
I posted this question and was told it was too complex to answer. I would like to know why. I would figure that a question meant for a college student could be answered by experts with "Masters and PhDs." Is there a table or chart I need to provide for the refrigerant, R-134A? I just need some help, haha