A nozzle is attached to a pipe as shown in Fig. 8-33. The inside diameter of the pipe is 100 mm, while the water jet exiting from the nozzle has a diameter of 50 mm. If the pressure at section 1 is 500 kPa, determine the water jet's velocity. 100-mm diameter 1 PI = 500 kPa Water (2) D₂ = ? 50-mm diameter Fig. 8-33

A nozzle is attached to a pipe as shown in Fig. 8-33. The inside diameter of the pipe is 100 mm, while the water jet exiting from the nozzle has a diameter of 50 mm. If the pressure at section 1 is 500 kPa, determine the water jet's velocity. 100-mm diameter 1 PI = 500 kPa Water (2) D₂ = ? 50-mm diameter Fig. 8-33

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hemispherical dome - SG = 0.8 4 m 60 kPa 3 m 3 m Water 2 m B
4. The pressure intensity at a point in a fluid is given 4.9 N/cm². Find the corresponding height of fluid when it 5. An oil of sp. gr. 0.8 is contained in a vessel. At a point the height of oil is 20 m. Find the corresponding m [Ans. (a) 5 m of water, (b) 6.25 m of cil is : (a) water, and (b) an oil of sp. gr. 0.8. (Ans. 16 m) and pbove it an oil of sp. gr. 0.8 for a depth of 2 m height of water at that point.
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft •(1) ↓² -0.12 ft -0.1 ft -free jet ft³/s lb/ft²
A U-tube of uniform cross-section has both arms open to the atmosphere. The U-tube contains three immiscible liquids, with density PA, PB, and pc, as depicted in the diagram below, where po is the atmospheric pressure. We denote h to be the depth of the open surface of liquid A on the left arm, relative to the open surface of liquid Con the right arm. I is the depth of the interface between liquid B and C on the right arm and 2l is the depth of the interface between liquid A and liquid B on the right arm. Po PA (c) Po PC PB е е (a) Explain why the liquid densities need to satisfy the condition PA PB PC. (b) Write down an expression for the pressure at depth z below the surface of liquid A in the left-hand part of the tube. Show that l < h < 2l if PB + PC < PA•
Please explain so I can understand
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
a=4 b=0 C=1
5-64. A thin rubber tube of 25 mm inside diameter is used to siphon water from the large tank of Figure 5.56. To prevent the tube from collapsing, the pressure inside the tube can not be less than 50% of the pressure outside the tube. Determine the smallest value of h to prevent the siphon from stopping due to collapsing of the tube. 2.5 m 5 m Figure 5.56 System for Exercise 5-64. THANK SUNTETICE Full Michifo Nas s itset SCH