A novelty gun shoots rolled up souvenir t-shirts towards spectators during a NY Mets game at CitiField. The MASS of each t-shirt is 0.457 kg and it is shot from the gun at a VELOCITY of 10 m/s. If the MASS of the gun is 10.0 kg, what is the VELOCITY (in m/s) that the gun recoils backwards when it shoots a t-shirt?

A novelty gun shoots rolled up souvenir t-shirts towards spectators during a NY Mets game at CitiField. The MASS of each t-shirt is 0.457 kg and it is shot from the gun at a VELOCITY of 10 m/s. If the MASS of the gun is 10.0 kg, what is the VELOCITY (in m/s) that the gun recoils backwards when it shoots a t-shirt?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the suffix meaning
Enginooring Mochanics: Sutca (1 Fint Scitester, Firt yoat, Academic yer 2020-2021 Deputtane of Civil Engnoeg Callege of Engincenng Lasenaty ut Mis Cm link on Miodle Instructor: Dr. Murtada Abass Mid-term Examination of E113 1 year 2020-2021 Date: March 5, 2021 Time: 20 Minutes Answer one question only which is assigned for you only Your Question is assigned via Mloodle in Ouizzes Section Your answer to the question will be submitted via Zoom Question: Determine the reactions of the truss shown in the Figure, 5 KN lom A جميلة محمد 15 کشيش lom IDM Page15
Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing
Problem- Cargo ships can cause a lot of air pollution.Solution- to use nuclear powered ships since they hold a lot of energy and can travel for long distances. How it will work is that it will need a nuclear reactor at the bottom of the boat to heat up the water and then turn it to electricity to power the boat. The boat will be made out of graphene which is a tough material to avoid any leaks in the boat. It will also contain many control rods because nuclear power is so powerful that it can create to much energy to handle. With control rods, you can slow down this process and keep it in a controlled manner. Since cargo ships are already is the ocean, there will be no need for any extra materials to make it work. -Do you think this will work? Why/Why not? -What do you think is wrong with it/ How can this be improved? Please send this to someone else I need to record 50 responses for a science project. Thank you!
1 The basic drilling process is that a at the bottom of_ grinds a hole through the rock layers.
ANSWER LETTER B AND D show solutions, for checking
Student Name: Reg. No: 1. Briefly describe Pascal's Law. Provide an examples of Pascal's Law applications in engineering. What is Revnolds Number what is the purnoss of Revnolds nunmber? State the
hi, i am looking for a complete answer height at which changes the path to target , total time to hit target, clearance according to the height of jake in question. please.
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
js ögLeull j in-- The car body is made of stainless steel low carbon steel O high carbon steel O fıne grained brass
DESCRIPTIVE GEOMETRY