A noise gate is a limiter that allows a signal to pass through only when it is above a set threshold True or False
Q: In this type of digital circuit, its output is dependent of the new input, previous state and clock…
A: A digital circuit is created using logic gates in which the input to the circuit and output of the…
Q: weighted-input DAC in that it requires only two resistor values.
A: Step by step explanation is in given below.
Q: A pulse is applied to each input of a 2-input NOR gate. One pulse goes HIGH at t = 0 and goes back…
A: Truth Table of 2 input NOR gate. INPUT INPUT NOR OUTPUT 0 0 1 0 1 0 1 0 0 1 1 0
Q: Using a multiplexer, design a circuit which its output is one if the majority of its input is one;…
A: Given data, Using a multiplexer, design a circuit whose output is one if the majority of its input…
Q: A voltage amplifier with gain 3 dB is cascaded with an attenuator of attenuation (ratio) of 1/v2.…
A: Refer to step 2 for the answer.
Q: *.Amplitude refers to the amount of voltage in one point in a circuit true False
A: Actually, the amplitude is the maximum amount of voltage in a given circuit.
Q: The input waveform shown in the figure below is applied to an inverter, which is used to operate a…
A: Below I have provided handwritten solution of the given question
Q: average propagation delay of a single gate of IC 7400. Determine the maximum average power…
A: Question :-
Q: A sequential circuit counts from 0 to 255 using JK flip-flop. If the propagation delay of each flip…
A: The above question is solved in step 2 :-
Q: Generally, when an output waveform is found to be incorrect, what is the next step to be taken?
A: GIVEN : when an output waveform is found to be incorrect what is the next step to be taken?…
Q: When used as a modulator in this circuit, the AND gate performs the same function. The receiver…
A: Adjustment is characterized as the most common way of superimposing a low-recurrence signal on a…
Q: A TTL gate has the following actual voltage level values: VIH(min) = 2.25 V, VIL(max) = 0.65…
A: Answer:
Q: explanatory text about what a flip-flop circuit performs and how it may be used Whether the circuit…
A: A flip flop is a two-state electronic circuit that can be used to store binary data. By changing the…
Q: What are the differences between logic gate types?
A: LOGIC GATE: A logic gate is basically the building block of the digital circuit. The logic gates…
Q: A race condition happens in an R-S latch when the inputs are indeterminate both zero either zero or…
A: The answer is given below:
Q: The process of adressing each input during one clock pulse is called
A: According to the Question we need to identify that" The process of addressing each input during one…
Q: The logic operation of XOR is often used to compare two inputs to determine whether they have the…
A: Given statement true or false
Q: The total RC delay of a fanout-of-2 inverter is *RC.
A: In computerized hardware, Fan-out of 4 is a proportion of time utilized in advanced CMOS…
Q: Observe the OLMC and programmed circuit. Complete the output waveform Note the clock, if you would…
A:
Q: A change in the height of the waveform represents a change in ... time current voltage speed
A: Given A change in the height of the waveform represents a change in
Q: (a) Draw the circuit of any one type of Band Pass Filter.
A: Note: we are only allowed to solve one question in one post. I am solving the first on here. To get…
Q: The AND gate in this circuit is functioning as a modulator in this circuit. The corresponding…
A: Modems are everyday devices in which modulators and demodulators are used. The word "modem" reflects…
Q: The maximum output voltage of a certain low-pass filter is 15 V. The output voltage at the critical…
A: Explanation: At critical frequency, the frequency is equal to the cutoff frequency. Low pass…
Q: Assuming it takes a signal 1ns to get through any type of gate, calculate the delay from time 0…
A: Given circuit contains many logic gates and the delay of each gate is 1 ns. Given that, the source…
Q: Can TT for ALU Control: Inputs Outputs ALUOP Binvert Ainvert Funct field. Fx Operation F5 F4 F3 F2…
A: Actually, the ALU is one of the part of computer. It is used to perform Arithmetic and logical…
Q: Q1: Design asynchronous counter that counts from 0 to 9 using positive edge- triggered D flip flop.…
A: I will provide the detail solution in the next step. I will provide the whole answer in four…
Q: A combinational circuit that selects one from many inputs are Select one: a. Decoder О Б. Епсоder O…
A: Defined the given statement
Q: Nyquist plot technique is the frequency response method for the analysis and design of control…
A: Nyquist plot of a frequency response is used in control or signal processing. So it helps in design…
Q: The AND gate in this circuit serves as a modulator in this circuit, which is a unique feature. The…
A: Introduction: Because it implements mathematical logic's logical conjunction (), the AND gate…
Q: Logic Circuits Design a 2-bit counter circuit using J-K Flip-Flops,
A: As per answering guidelines, solving the first question
Q: A magnitude comparator compares two binary numbers and determines if one number is greaterthan, less…
A:
Q: The number of gate inputs that can be driven by a single output without exceeding current rating of…
A: Option (a) fan out is correct.
Q: Define the term short-circuit evaluation.
A:
Q: Q1 Using a multiplexer design a combinational circuit design defined by the following boolean…
A:
Q: The full-wave controlled rectifier circuit has
A: Option E
Q: The envelope detection of ASK signal can be done by a O a. diode Ob. O b. product demodulator Oc…
A: ASK stands for amplitude shift keying where amplitude of carrier wave varies.
Q: In SSI, number of gates is usually less than 10 in a single package Select one: O True False
A: An integrated circuit (IC) containing digital gates and made up of silicon material. It is otherwise…
Q: The final amplifier of either FM or AM transmitter operates as Select the correct response: Class A…
A: the answer is given below:-
Q: A multiplexer is a digital circuit that has a multiple inputs and single output. false true حفظ…
A: Here have to determine correct option for multiplexer Input output.
Q: A positive-going pulse is applied to an inverter. The time interval from the leading edge of the…
A: A positive-going pulse implies a pulse going from LOW to HIGH. So, input goes LOW to HIGH whereas…
Q: Gate A has a greater propagation delay time than gate B. Which gate can operate at a higher…
A: The propagation delay time of a gate limits the frequency at which it can be operated. The greater…
Q: In common collector amplifier, if the output voltage Vout = 20mV, then the input voltage Vin O 20mV
A: Explanation: The common collector circuit have a voltage gain of almost unity. that means: = Vout…
Q: he attenuation in the pass band or stop band is called a. Transition band b. Ripple c. Cutoff…
A: The attenuation in the pass band or stop band is called Transition band
Q: Ramp signal are use in PWM demodulator True False
A: PWM: PWM stands for Pulse Width Modulation. The general purpose of Pulse Width Modulation is to…
Q: How does excessive loading affect the noise margin of a gate?
A: Given: How does excessive loading affect the noise margin of a gate?
Q: A fusing rating is 45 A?s of SCR. The device is being used in a circuit where it could be subjected…
A: your question is about the maximum allowable duration of such a surge is what ? data:- A fusing…
Q: When the frequency of the input signal to a CMOS gate is increased, the average power dissipation(a)…
A: Given: When the frequency of the input signal to a CMOS gate is increased, the average power…
A noise gate is a limiter that allows a signal to pass through only when it is above a set
threshold
True or False
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- A race condition happens in an R-S latch when the inputs are indeterminate both zero either zero or one both one This is the time needed by a gate in processing its input signals before the output signal can be generated propagation delay time threshold time setup time Ohold timeDepending on the value of input and reference voltage a comparator can be named asPractical Usage of Logic Gates Design Problem A motor car manufacturing company has manufactured a motor car protecting circuit to warn if there is a movement in the car when the engine is not on or when there is damage to a shutter. This has three sensors to detect whether the engine is on and another sensor to detect whether there is a damage to a shutter. Another sensor is there to detect whether the car is moving. This circuit is designed with three basic circuits. One of these is a NOT gate and the other two gates should be included in the empty boxes. What are the logic gates suitable for these? Draw the circuit. Practical Usage of Logic Gates Engine sensor Shutter damage alarm signal sensor Movement sensor
- 1- A combinational circuit is defined by the following three functions: F1= XY + XYZ F2= XY + XYZ F3- XỸZ + 7Z Design the circuit with a decoder and external gates.Full adders circuit can be implemeted by Select the correct response: NAD and OR gates multiplexers half adders decodersWrite the Boolean expression for a four-input NOR gate. F(A, B, C, D) =
- For a TTL gate , the sink current is higher than the source current Select one: True FalseIn SSI, number of gates is usually less than 10 in a single package Select one: True O FalseA positive-going pulse is applied to an inverter. The time interval from the leading edge of the input to the leading edge of the output is 7 ns. This parameter is(a) speed-power product (b) propagation delay, tPHL(c) propagation delay, tPLH (d) pulse width
- Generally, when an output waveform is found to be incorrect, what is the next step to be taken?1- A combinational circuit is defined by the following three functions: F1= XY + XYZ F2= XY + XYZ F3= XỸZ + YZ Design the circuit with a decoder and external gates.2- L The output of a logic gate is 1 when all the inputs are at logic 0 as shown below. What is the gate called? a) NAND b) AND c) XNOR d) NOR input A input B output 0 0 1 0 1 0 1 0 0 1 1 0