A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.

Q: 427 3. 127 307 In the gear train shown in sketch c the pinion rotates at 650 rpm and transfers 5.9…

A:

Q: Consider the epicyclic gear system. Set up a tabke of wheel speeds for the cases where all the…

A: Angular Velocity is the revolutionary or angular motion of a body. It is equal to the distance…

Q: A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift…

A:

Q: Calculate The angular speed of the gear wheel in rad/s

A: Relationship between no of teeth (T) and speed (N) is given by, Ng/Np = Tp/Tg so, Ng = (Np × Tp)/…

Q: In an epicyclic gear of the sun and planet' type has a fixed outer wheel A, sun wheel S rotates at a…

A: GivenTP=27TS=18Ns=600 rpm

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: Determine the horsepower of a 6 cylinder 4 stroke continental engine having a bore equal to 3.875 in…

A:

Q: 2. The valve timing for a four stroke petrol engine is as follows: inlet open 4° L, inlet closes 50°…

A:

Q: at distances of 100 mm from the central plane of the middle eccentric, find the amount of he masses…

A:

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum.  The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: A vehicle engine is producing a brake power of 56 kW with a torque of 132.2 Nm. The final drive…

A:

Q: Q10:- An epicyclic train of wheel is arranged as shown in the Fig. below. How many revolutions does…

A:

Q: 7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative…

A: (a) Write the given data. Tf=48Df=10.5 inTs1=30Ts2=26Ts3=23Ts4=20Ts5=16Ts6=12Nf=105 rpmFf=28 lb

Q: An eccentric cam has diameter of disc 80 mm and an offset 30 mm from centre of rotation, operates a…

A: We have a flat faced follower that is operated by an eccentric cam with a disc diameter of 80 mm and…

Q: Please solve this problem, Thank you  Problem : Cone A turns 126 rpm and cone B turns 162 rpm.…

A:

Q: A significant disadvantage of using a flywheel with a reduced moment of inertia would most likely…

A: Given:   To select the correct option for the disadvantage of using a flywheel with less moment of…

Q: 1-)The diagram of the change of cutting force for the cutting work performed with the press seen in…

A: Given data   Engine revolution =  900 rpm Flywheel revolutions = 60 rpm. Themoment of inertia of…

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to…

A: V-belt pulleys (likewise called vee belt bundles) are gadgets which send power between axles by the…

Q: Chain 8A having a pitch of 12.7 mm is used to connect 5 KW, 1400 rpm motor to a drilling machine.…

A:

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift…

A: Given Datam=18T/hrN=1750rpmS=33.5mV=61m/min

Q: For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each…

A: The objective of the question is to analyze the capabilities of a gearbox in a hot strip mill. This…

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: i need the answer quickly

A:

Q: moment of inertia of the flywheel is

A: Given; A flywheel is attached to an engine to keep its rotational speed between; ωmax=110…

Q: el. 00

A:

Q: A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal…

A: Given data: CD=146 mmϕn=20°Z1=26Z2=34 Need to determine  the transverse pressure angle in degrees.

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.