A metal boom OA Is shown in the figure below is supported by 2 cables AC and AB and held in pesition by ball and socket joint at joint O. If the angle a is taken from the y-axis and force P is in XY plane. Determine the reaction force(s) at O and tension in both the cables. Choose the value for P between 200 KN to 500KN Choose the value for the angle (a) between 20° to 80 510 mm 320 mm 270 mm B 360 mm G00 m

A metal boom OA Is shown in the figure below is supported by 2 cables AC and AB and held in pesition by ball and socket joint at joint O. If the angle a is taken from the y-axis and force P is in XY plane. Determine the reaction force(s) at O and tension in both the cables. Choose the value for P between 200 KN to 500KN Choose the value for the angle (a) between 20° to 80 510 mm 320 mm 270 mm B 360 mm G00 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FN= 119, MN= 85, SN= 93
In this statics problem I am given a triangular distributed load on a cable. Attached is the given info for the problem. I know the basic steps to complete the problem but I am having issues figuring out where the triangular distributed load and 15 degrees given work into the problem. I’ve tried finding the Moment around B with the distributed load and then the two components of Tension at A (using sin(15) and cos(15) respectively but this did not work.
Homework: Cables are attached to pins at A, B, and E as shown in Figure below. Determine the horizontal and vertical components of the pin reaction at C on member DCA. Neglect the weights of the members and the pulleys. 5 mm mm 3 mm Cable 200 Nimm 3 mm Smooth pulleys 50 Nm 200 N 3 mm D
SHOW COMPLETE SOLUTION
A single axle with 32 kips load will cause the same amount of damage per pass as caused by ______ passes of standard 18 kips axle. Group of answer choices a. 10 b. 12 c. 14 d. 16
What is the fixed end moment at A? 10 kN 3kN/m D 3m B 4 m 4 m
Q.1) For the frame shown in figure have a two- member (ABOC and EDC) and is pin connected at E, C and A. If a 750 N force is applied directed vertically (a) at B, (b) at D. Determine the horizontal and vertical components of reactions at pin E and A. 50 mm 170mm 125 mm C 75 WE
200-Ib block is suspended from an inextensible cable which is wrapped around a drum of 1.3-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of Inertia lG = 10 Ib-ft-s^2 At the instant shown, the velocity of the block is 5 ft/s directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 60 Ib-ft, determine the velocity of the block after it has moved 4.2 ft downward (in ft/s).
For a helical spring the slope of helix may be assumed small, is required to transmit a maximum pull of 1 kN and to extend 10 mm for 100 N load. The mean diameter of the coil is to be 100 mm. The diameter of wire is 100 mm. Calculate the no. of coils required? (G = 100 GPa and fs = 100 MPa)
Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value of a = SN and b = MN meters. The equivalent of 0 is 30 degrees Note: MN = 88 FN = 88 SN = 47 a Hinge b Cable m Beam com M Rope
Answer in three decimal places
Can you answer this question please.