A medium drive of a steel hub of a gear with an outside diameter of 80 mm on a steel shaft is required. a) Make the dimensional decisions for a 49-mm basic size with a medium drive fit for the hub and shaft, and specify dimensions with tolerances for the shaft and the hub bore for the fit. b) When the interference pressure "p" is at a minimum (p at Smin) for the specified tolerances how much torque (in Nm) can be transferred with the medium drive fitted assembly if the steel to steel friction is 0,8 and the hub of the length is 170 mm. E=207 GPa

A medium drive of a steel hub of a gear with an outside diameter of 80 mm on a steel shaft is required. a) Make the dimensional decisions for a 49-mm basic size with a medium drive fit for the hub and shaft, and specify dimensions with tolerances for the shaft and the hub bore for the fit. b) When the interference pressure "p" is at a minimum (p at Smin) for the specified tolerances how much torque (in Nm) can be transferred with the medium drive fitted assembly if the steel to steel friction is 0,8 and the hub of the length is 170 mm. E=207 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-Show how the roughness is indicated for a Surface to be coated, obtained by any production method with N6 showing max. and min roughness. 3- gearing is suitable for two shafts at 90°. : Draw five turns of a compression spring of wire diameter 6mm, pitch 12 num and outside diameter of 38mm.
There are two pairs of closed soft tooth surface spur gears A and B,Parameters of A: modulus m = 2mm, number of teeth Z1 = 40, Z2 = 90 , width of teeth b = 60mm.Parameters of B : modulus m = 4mm, number of teeth Z1 = 20, Z2 = 45 , width of teeth b = 60mm.The accuracy of the two pairs of gears is grade8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason.
I need answer in 10 minutes please quickly
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
Hand written plz
Please help me finding this question. Power = 6 kW
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
please send handwritten solution Q4 part d e f
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio
5.A pair of gears has these parameters: teeth of two gears are Z1=26, Z2=52, modulus m=1.25mm. Please calculate (1)the radius of reference circle of two gears, r1 and r2 (2) The pitch of this pair of gears, p (3) The standard center distance, a (4) Now two gears are mounted with a'=49mm, calculate the radius of two pitch circle for two gears, r1' and r2' . (5)The ratio of angular velocity of two gears, i.