Answered: A manometer is attached to a conduit as…

A manometer is attached to a conduit as shown. What is the pressure at A in kPa. Choices are: A. 38.25 kPa B. 38.85 kPa C. 32.85 kPa D. 38.45 kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Draw the the following views of the given figure. Thank you.

A: Answer We can draw the Orthographic views based on the given Isometric views using following steps…

Q: Determine the internal normal force, shear force, and bending moment at point A in the beam. Note…

A: Given : Determine the internal normal force, shear force and bending moment at point A ?

Q: Given the arc distance (L) of a horizontal curve = 475.81' The degree of curve (Daº) = 06°-18'-18"…

A: Objective: To determine the deflection angle ∆ for the given horizontal curve. Given: Arc distance…

Q: A circular water tank of 2 m diameter has a circular orifice of diameter 0.1 m at the bottom. Water…

A: Given- Water tank diameter D=2 m, Orifice dia d=0.1 m, Flow rate Q=20 litre/s, Coefficient of…

Q: FRONT VIEW RIGHT SIDE VIEW FRONT VIEW RIGHT SIDE VIEW

Q: The configurations of parallel and single sections of pipelines from A to B are shown below.…

A: Given Data Find equivalent diameter of pipe

Q: A production well was discharged and tested through an atmospheric silencer at sea level (1 bar…

A: (1)

Q: 31. It offers higher performance in tensile stress, yield stress, bending, weld ability and…

A: Explanation : (31) Providing Higher performance under tensile stress, yield stress or bending is a…

Q: In a stream line steady flow, two points A and B on a stream line are 1 m apart and the flow…

A: Given- Distance s=1 m, velocity at A- VA=2 m/s, VB=5 m/s.

Q: Do people in Detroit Michigan live in big houses or smaller ones?

A: Detroit- It is a city in the state of Michigan (US).

Q: Problem Determine the height of a rectangular weir of length 6 m to be built across a rectan- gular…

A: Given- Length of weir L=6 m, Depth of water H1=1.8 m, Discharge Q=2000 lit/sec, Coefficient of…

Q: Part II. Complete the table below. Unit of length is meter. For area computation, use the adjusted…

Q: Q-7 In a homogeneous unconfined aquifer of area 3.00 km², the water table was at an elevation of…

A: Given data: A homogenous unconfined aquifer of area, A = 3 km2 The water table was at an elevation…

Q: Determine the deflection at the left overhang of the beam loaded as shown below using double…

A: Given Data E = 200 GPA I = 1460 × 106 mm4 Find deflection at the left overhang of the beam…

Q: Determine the deflection at the right overhang using either the Method of Virtual Work or the…

A: A simply supported beam hinged at B and roller supported at E is given. Loads UDL of 40 kN/m from A…

Q: For the following steel frame (E = 200,000 MPa; l = 500 x 106 mm4), use the virtual work method to…

A: E= 200,000 MPa I= 500×106 mm4 To determine- a) The horizontal displacement at point B b) The…

Q: The effective stress strength parameters of soil are c'= 10 kPa and p = 30°, then shear strength on…

A: Given data: Effective stress strength parameters of soil, c'=10 kPa Angle of shearing resistance,…

Q: te from the surface of a 3,650-acre lake is 100 acre-ft/day. Estimate the depth change in the lake…

A: According to given data The evaporation rate from the surface of a 3,650-acre lake is 100…

Q: There is a reservoir covering a 500-hectare area that has a constant draft of water pumped from it.…

Q: For the rigid frame shown, calculate the horizontal deflection at point C. Members have the same…

A: E=210 GPa=210 x 106 kNm2I=1440 x 104 cm4 = 0.1440 m4EI=30.24 x 106 kN.m2Angle that BC makes with…

Q: The soil profile at a site up to a depth of 10 m is shown in the figure (not drawn to the scale).…

A: Given- Surcharge- q=70 kN/m3,Soil depth =10 m,Water table 3 m below GL, Soil unit weights and soil…

Q: If the force F shown in Fig. P-017 is resolved into components parallel to the bars AB and BC, the…

A: Given : The magnitude of component parallel to bar BC = 4 kN What are the magnitude of F and it…

Q: Suggest practical situations where parallel pipe networks may be found.

A: Parallel Pipe: Pipes are said to be in parallel if the supply pipe or the main pipe divides into two…

Q: shown. Determine the resultant of the forces applied on a simply supported beam as skal/m 50.KN O

Q: 6. The overhanging steel beam ABC carries a concentrated load P at end C. For portion AB of the…

A: Given: W 360 x 101 section I = 301 x 106 mm4 E = 200 GPa P = 250 kN L = 5 m a = 1.2 m To find: a)…

Q: The 250-ft-long hose is made of a material having a roughness of = 0.0005 ft. (Figure 1) Figure 80…

Q: 8.14 Calculate the moment of inertia with respect to the X-X cen- troidal axis of the built-up…

A: Given data:-

Q: The bars in the following figure have the same cross sectional area of 0.5 in. There is no stress…

A: Given data:- The given cross-sectional area, 0.5 in The given load in each bar if the temperature…

Q: 16. Which one is the toughest? (a) CFRP (b) GFRP (c) High Strength (d) Mild Steel 17. A step in…

Q: Give the procedures in finding the friction factor fusing the Moody Chart. Provide illustrations.

A: The Moody chart is a non-dimensional graph that shows the relationship between the relative…

Q: A sand specimen was compacted in a direct shear device and loaded with a vertical stress of 150 kPa.…

A: According to given data . A sand specimen was compacted in a direct shear device and loaded with a…

Q: Problem 2: A bar is made from bonded pieces of steel (E = 29x10 psi) and brass (E = 15x10 psi).…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 Determine the max. stress in the steel and brass when a…

Q: A toxic pollutant with an initial concentration 598.08 is being treated in a batch reactor.…

A: According to given data A toxic pollutant with an initial concentration 598.08 is being treated in…

Q: Find the stresses in members BC, BD, and CF for the truss shown in Fig. P-113. Indicate the tension…

Q: The cable is subjected to the uniform loading. If the slope of the cable at point O is zero,…

Q: 4 kN/m 12 m BO 6 m 10 kN 5 3 C hinges D 5 m * 3 m 4 m 2 kN/m E 10 m F 5 3

Q: Construct the shear and moment diagram of the figure below. Note: Support reactions is zero. Thus,…

Q: Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 8 kips/ft,…

Q: Draw the following views of the figure below. (You can use AUT0CAD in showing different views)

A: Answer We can use the following steps to draw the orthographic views using given Isometric views in…

Q: A project to move packed earth requires you to decide whether to use a dozer/scraper operation or…

A: Givene Data : Excavator costs = $95/hr Cyclic time = 0.28 min Bucket head capacity =5.0 cy Truck…

Q: Describe how wood can be attacked by fungi.

A: Fungal attack on the wood: The presence of moisture content in the wood will be the reason for…

Q: As the depth chnges negatively means decreasing , can you please explain what are some measures to…

A: Yes . In the question it can be clearly seen that - the depth is decreasing by 153.65 cm The reason…

Q: The following figure shows a clayey soil, that is 1 dimensionally loaded by a vertical stress of do'…

A: Answer (1) To calculate the Cv for the soil based on the given data we have Terzaghi's 1-D equation…

Q: Show your neat and complete solution LINE LENGTH BEARING LATITUDE DEPARTURE AB 732.72 N00°42'E…

Q: A completely mixed tank has a volume of 10 Litres. It contains 0.5 Litres of dirty water with a…

A: According to given data A completely mixed tank has a volume of 10 Litres.It contains 0.5 Litres of…

Q: 150-mm diameter Section A (a) 100-mm diameter 30° Section B

A: Energy is lost when it is changed from one form to another, transported from one location to…

Q: The two forces are equivalent to a force R that has a line of action passin through point A.…

A: A force system is given. A 90 N acts along (+)ive y-axis and a 100 N force acts along (-)ive x-axis.…

Q: What is the full length of a superelevation transition with d - 200 (1:d slope). e - 0.08, and two…

Q: Determine the bending strength capacity (Mu) that can be imposed on a floor system consisting of 4…

Q: What will be the theoretical maximum capacity (to nearest 10 units) for a single lane of highways…

A: Given data: Speed of the traffic stream, v = 40 kmph Theoretical maximum capacity, C =?

Concept explainers

Pressure and Stress

Question

A manometer is attached to a conduit as shown. What is the pressure at A in kPa.
Choices are:

A. 38.25 kPa

B. 38.85 kPa

C. 32.85 kPa

D. 38.45 kPa

Sp.gr. of liquid B = 10
h = 150 mm
A
Water
d = 450 mm
D
h=150
#=450
(sp. gr. = 10)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(ơallow)t (MPa)=6 (ơallow)c (MPa)=8 α (º)=60 t (mm)=40
A uniform edge load of w₁ = 540 lb/in. and W2 = 400 lb/in. is applied to the polystyrene specimen. Ep = 597 (10³) psi and vp = 0.25. (Figure 1) Figure T W₂ b - < 1 of 1
L=2cm p=20kN Strength of material question need help with solution
EHide blocks Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. Tensile stress-strain diagram 450 400 350 300 250 150 100 50 0.15 02 0.25 0.3 0.35 Strain 300 250 200 150 100 50 Stress (Mpa) (dy saas
civil engineering (Article) Determine O 3 ↑ 0.3mm ↓ A=amy Top plate UNIT V=0.3 m/sec S=0.88 M = 0.65 centi poise → Bottom plate Direction of shear force on top plate Bottom plate & fluid element kinematic viscosity Resistive force.
Determine the components of reactioe atC. SON
Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction. S11=7.6 (TPa)-', S12 = - 2.8 (TPa)-', S44 = 8.6 (TPa) -!
Equivalent G = 6M = 4L = 8
The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. AB= tolerance is ± 1 in the 3rd ficant digit. AG = BC = BG= CD = CF = i i i i i B i G 2.8 KN d F 6.3 KN 3 3 3 3 3 3 KN KN KN kN kN D E
Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below. Cantilever beam is loaded at the tip with 100 kN. In the cross-section height of steel is 50 mm, height of the aluminum is 350 mm and height of the brass is 100 mm. Modulus of clasticity for the materials are given as; Steel, Est = 200 GPa, Aluminum, E = 70 GPa and Brass, Esr= 105 GPa. Find the maximum axial stresses under given loading for Steel, Aluminum and Brass, separately. Steel 150 kN 500 mm 50 mm Aluminum Aluminum 350 mm Brass Brass 100 mm Cross Section of the 5 m Beam Fixed Side view of the Beam Support
o (MPa) 750 B -F 600 A parallel Ty = 450 300 150 D € (mm/mm) 0.01 | 0.02) 0.03 0.04 Ey = 0.006 - EOC- O7 0.023 The stress-strain diagram for an aluminum alloy that is used for making aircraft parts is shown in Fig. 3-19. If a specimen of this material is stressed to 600 MPa, determine the permanent strain that remains in the specimen when the load is released. Also, find the modulus of resilience both before and after the load application.