A man having a weight of 174 lb attempts to hold himself using one of the two methods shown. Determine the total force he must exert on bar AB in each case and the normal reaction he exerts on the platform at C. The platform has a weight of 26 lb . (Figure 1) igure 1 of 1> (a) (b)

Q: The frame is loaded as shown. The 150 lb/ft distributed load is perpendicular to member AC. The…

A:

Q: The bars AB and AC are joined by a pin at A and a horizontal cable. The vertical cable carrying the…

A: Apply the conditions of equilibirum  RBy+Rcy=200(9.81)=1962N Calculate the length of the rod AB…

Q: he 30-lb homogeneous bar AB supports the 60-lb block. The ends of the bar rest on frictionless…

A:

Q: Q4/ A skeletal diagram of a hand holding a D load is shown in the upper figure. If the load and the…

A: F.B.D of arm AB,

Q: Two identical spheres weighing 100 KN each are placed in a container such that the lower sphere will…

A:

Q: - In the side view of a 70-kg television resting on a 24-kg cabinet, the mass centers are labeled G,…

A: Mass of telivision  = 70 kg Mass of cabinet = 24 kg

Q: f the maximum force that any member can support is 11.1 kN in tension and 8 kN in compression,…

A:

Q: The smooth disk shown below is pinned at D and has a weight of 20 lb. Neglecting the weights of the…

A: For the given system  weight of the disk (W) = 20 lb    To determine  Reaction at C and reaction…

Q: A 600-lb crate is supported by several rope-and-pulley arrangements as shown. Determine for each…

A: Given data: The weight of the crate is W=600 lb. The free body diagram for the pully a is:…

Q: Example : The floor crane and the driver have a total weight of 2500 Ib with a center of gravity at…

A: The free body diagram of the whole system is as follows:

Q: Two massless and frictionless pulleys are used to drag a large mass (m = 645 kg) up an inclined…

A:

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A:

Q: Two horizontal beams are used to balance the masses A, B, and C, as shown in the figure. Each beam…

A: Given data Mass(Mc)= 30kg Need to determine the tension force in each cable

Q: A puck weighs 10 lb and rests on the center of the frictionless surface of the ramp supported in…

A:

Q: A 40-lb force is required to operate the foot pedal. Determine the tension, T' in the connecting…

A: Given data: FA=40 lbC=B=9 in Need to determine the tension (T).

Q: Determine the force in member BC. a 4.50 kN(C) c 8.00 kN(C) b 6.00 kN(C) d 14.00 kN(C) Determine the…

A: The free-body diagram of the given truss can be drawn as below, Here RC is the horizontal reaction…

Q: Q4- Determine the horizontal force * .(P) required for equilibrium 41.212 kN 90.111 kN 77.986 kN…

A:

Q: The homogeneous cylinder of weight W = 100N rests in a frictionless right-angled corner. Determine…

A:

Q: ted by the lifing device which hoocks over the end lips of the drum. Determine the tension T in each…

A: Sketch the free body diagram of the drum as follows:

Q: The 10-kN and 40-kN forces are  applied to the pins at B and C,  respectively. Calculate the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: The horizontal reaction at support O will be at the 100 lb 1 ft 50 lb 3 ft 3 -3 ft 150 lb O non of…

A:

Q: 12. Determine the magnitude of the reaction force at pin support B when 0 = 30°, as shown, to…

A: The magnitude of the reaction force at pin support B: RB = 25.98 kN (Option D)

Q: deflection of the uniform 100-kg beam the 60-kg boy exerts a pull of 150 N on the rope rigged as…

A: Given that ;  WB=60kgWbeam=100kgT=150N

Q: 45kg block is placed on an inclined plane whose base is double its height. Determine the force to…

A: To determine the force required to keep the block in equillibrium.

Q: The man is holding up the 35-kg ladder ABC by pushing perpendicular to ladder. If the maximum force…

A: Given:- Mass of the ladder (m) = 35 kg Force (F) = 400 N To Find:-  Angle (θ )

Q: If in equilibrium, the anticlockwise turning effect of force F must equal the clockwise turning…

A: Calculate the force F by applying moment at the pin point as follows: ∑MO=0F×0.25=5×0.5F=10 N This…

Q: The 100 kg C ring moves on the BD rod without friction. Calculate the force on the AC chain for the…

A:

Q: A system of three pin connected bars takes the depicted equilibrium position under the given loading…

A: Given data: Three-pin connected bars.

Q: The mass center G of the 1300-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: Determine the maximum weight of the bucket that the wire system can support so that no single wire…

A:

Q: Q4) Determine the magnitude of the horizontal force F and the support reactions at pin A. If the…

A: Drawing FBD:

Q: Q4) Determine the reactions in support A and support C.

A:

Q: Determine the ratio P/Q of the forces that are required to maintain equilibrium of the mechanism for…

A: In the given diagram of mechanism, the vertical distance between fixed pin support and the point of…

Q: Q2: The 80-lb block C rests on the uniform 15-1lb bar AB. The cable connecting C to B passes over a…

A:

Q: Q2. The 80-lb block C rests on the uniform 15-1b bar AB. The cable connecting C to B passes over a…

A:

Q: Engineering mechanics – statics 1$t stage Lecturer: Amany Barrak Example : The floor crane and the…

A:

Q: The crane pulls a fixed object in D using the CD cable. The crane is supported on bearings at E and…

A:

Q: The cords ABC and BD can each support a maximum load of 100 lb. Determine the maximum weight of the…

A:

Q: problem r1

A:

Q: The pin, attached to member BCD, passes through a smooth slot in member AB Take w = 120 lb/ft.…

A:

Q: The window washers A and B support themselves and the 15-kg uniform plank CD by pulling down on the…

A:

Q: b) Identify and determine the tension in the cables AB, AC and AD in order to support the 100-kg…

A:

Q: F1 F2 B 8 ft E |F 6 ft H. –6 ft 6 ft -6 ft NE A,

A:

Q: Determine the force in the 197 N/m stiffness spring when the system is in equilibrium. (include…

A:

Q: A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in…

A:

Q: he elements of the spring loaded mechanism for the car tailgate are shown in the figure. For the…

A:

Q: Q19. As shown in the image below, the 3.7-Mg four-wheel-drive SUV tows the 1.3- Mg trailer. The…

A: Given;The weight of SUV, W = 3.7 Mg = 3700 kgThe weight of trailer, w = 1.3 Mg = 1300 MgThe traction…

Q: he uniform 15-m pole has a mass of 165 kg and is supported by its smooth ends against the vertical…

A: Draw the free body diagram for the above problem.

Q: The winch cable on a tow truck is subjected to a force of T = 8 kN when the cable is directed at =…

A: T=8kN

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.