a) Make a simple wiring connection layout of your own house like the image shown below. The layout will be according to your house and the equipment used in your house. Mention the total load and current drawn by each room/spaces and the recommended size of cables to be used beside the cable lines. The following image is just an example and it is not complete. You may use standard symbols of the equipment or draw with appropriate label, i.e. fan, light, switchboard, MCB etc.

a) Make a simple wiring connection layout of your own house like the image shown below. The layout will be according to your house and the equipment used in your house. Mention the total load and current drawn by each room/spaces and the recommended size of cables to be used beside the cable lines. The following image is just an example and it is not complete. You may use standard symbols of the equipment or draw with appropriate label, i.e. fan, light, switchboard, MCB etc.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter5: Conductor Identification, Switch Control Of Lighting Circuits, Bonding/grounding Of Wiring Devices, And Induction Heating

Section: Chapter Questions

Problem 9R: Complete the connections for the diagram. Installation is cable.

See similar textbooks

Similar questions

Grounding Lighting Fixtures. There are specific requirements for grounding lighting fixtures. How must they be grounded and with what size conductors? Be sure and cite the code in your answers.
5 a) Discuss Electricity power generation and distribution to residential properties. b) with diagrams explain how a Distribution Board is wired to provide electricity to a residential property. c) Explain the following materials and Accessories. i. Male and female bushings. ii male and female adaptors iii. Couplings. iv. Wire/cable sizes and their us
6. Since the voltages across each branch circuit in a residence are the same, these circuits areA. connected in series.B. connected in parallel.C. controlled circuit configurations.D. complex circuit configurations. I'm not sure if it's the letter B or C, could you help me with the correct answer.
12 - Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters and three-wire cables up to ……... meters are used in standard designs. A) 10-150B) 40-500C) 50-195D) 30-230E) 200-1000
Load in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a maintenance engineer, you need to proposed cable size for the load, Determine the following issues. 1) Calculate current demand for the circuit. 1) Detemine suitable MCCB (Model and nominal current rating) should be used to protect the load against over-current. im Propose suitable cable size for the load in Figure 1. iv) Calculate voltage drop of the proposed cable WITHOUT consider the cable reactance and voltage drop correction due to higher cable operating temperature v) Calculate voltage drop of the proposed cable BY consider the cable reactance and voltage drop correction due to higher cable operatıng temperature vi) If the multicore PVC eable is change into 3 single core PVC cables, what the suitable cable size. All other multicore cables not available. (25 + variable x) m (A) 30 m (B) (15 + variable b) m (C) Multicore PVC cable MCCB 95 kW. (400 + variable y) V. 0.85 p.f. Load MSB…
Complete the connections for the diagram. Installation is cable.
For Figure 1 switch circuit: a. derive the switching algebra expression that corresponds one to one with the switch circuit. b. derive an equivalent switch circuit with a structure consisting of a parallel connection of groups of switches connected in series. (Use 9 switches.) c. derive an equivalent switch circuit with a structure consisting of a series connection of groups of switches connected in parallel. (Use 6 switches.) B' Figure 1. Switch Circuit
Explain the diagrams
1. Draw a Wiring Drawing of this circuit.
What is the best way to define series and parallel wiring of circuit elements?
Explain what is Grid system?
Determine the size and type of wire to he installed to a building with temperature that reaches 80-90 degrees with the following loads. 10pcs. Of 200- watt bulb 15pcs. Of 100-watt bulb Single phase, 230 source. And if you would be installing the wire inside an EMT conduit, what size would you use assuming that there would be 4 wires inside the EMT