A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, as shown in Fig. 3. When the water level reaches 5 m, the gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens. 4.2 m 5m R=0.8 m | 0.8 m Fig. 3

A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, as shown in Fig. 3. When the water level reaches 5 m, the gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens. 4.2 m 5m R=0.8 m | 0.8 m Fig. 3

Name: A long solid cylinder of radius 0.8 m hinged at point A is used as an
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A long solid cylinder of radius 0.8 m hinged at point A is used as an automaticgate, as shown in Fig. 3. When the water level reaches 5 m, the gate opens byturning about the hinge at point A. Determine (a) the hydrostatic force acting onthe cylinder

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
4. A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25KN. Determine the vertical force required to lit the gate when its upper edge is 6m below the free water surface and coefficient of friction between the gate and guides is 0.15. Determine the center of pressure acting on the gate. Water 6 m Gate- F-
Q.1: An inclined, circular gate with water on one side is shown in the figure below. Determine the total hydrostatic force acting on the gate and the location of the center of pressure. Water surface 1.5 m 60 Gate Side view Gate Top 1 m view Q.2: In the figure shows a curved surface LM, which is in the form of a quadrant of a circle of radius (2.4 m), immersed in the water. If the width of the gate is unity, calculate the horizontal and vertical components of the total force acting on the curved surface. Free water surface 1.2 m 2.4 m TTTTTTTM Curved surface
A rectangular gate which is inclined 90-degrees with respect to the horizontal and has a 3.5 m width and 17.0 m height, is being submerged in water with its top edge is 4.4 m above the water surface. Find the induced total hydrostatic force(in kN) on one side of the gate. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
1- The flow of water from a reservoir is controlled by a5-ft-wide L-shaped gate hinged at point A, as shown in Fig. If it is desired that the gate open when the water height is 12 ft, determine the hydrostatic and find its point of acting. (w for water = 62.4 Ibf /ft³) B Gate 15 ft 12 ft
A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, When the water level reaches 5 m, the gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens and (b) the weight of the cylinder per m length of the cylinder.
A triangular lamina is immersed vertically in water in such a way that its 6 m wide horizontal base is 8 m below the free surface of water and the apex is 4.5 m above the base. Find : (1) Total pressure force and (ii) Position of centre of pressure. 7 Water G 6m h 3 4.5m 8m
A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown in the figure below. When the water level reaches 15 ft, the cylindrical gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens. (b) the weight of the cylinder per ft length of the cylinder.
Q. 2 (b) A rectangular plate 0.6 m wide and 1.2 m deep lies within a water body such that its plane is inclined at 45° to the horizontal and the top edge is 0.70 m below the water surface. Determine the total pressure force on one side of the plate and the location of the centre of pressure. F M Water h A 0.6m XE В' B 0.7m 45° Fig.1-Q.2(b) D 0.6m G 1.2m 45° 45°
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
help, asap, with complete solution PROBLEM 3: The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point B. For a gate width of 7 feet, A. Determine the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips.
A sliding gate of height 1.4m and width 2.8m lies in vertical plane that weighs25kN. When the gate upper edge is 6m below the free water surface and coefficient of friction between the gate and guides is 0.15. Determine the center of pressure acting on the gate.