A load Pis supported by two springs arranged in series. The upper string has 20 turns of 25-mm diameter wire of 150 mm. The lower spring consists of 15 tums of 12-mm diameter wire on a mean diameter of 130 mm. The load produces a total deflection of 80 mm. G= 83 GPa a) Compute the value of the load P. b) Calculate the maximum shearing stress in the upper string. c) Calculate the maximum shearing stress in the lower string.

A load Pis supported by two springs arranged in series. The upper string has 20 turns of 25-mm diameter wire of 150 mm. The lower spring consists of 15 tums of 12-mm diameter wire on a mean diameter of 130 mm. The load produces a total deflection of 80 mm. G= 83 GPa a) Compute the value of the load P. b) Calculate the maximum shearing stress in the upper string. c) Calculate the maximum shearing stress in the lower string.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. 400 mm BC The maximum safe value of Pis 30° P 480 mm kN. (Round off to one decimal place)
Q.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11800 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 2900 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 92 in., b = 40 in., and c = 34 in.
Solve this Portion Use problem 3.52. Add a force of 500 kN that is perpendicularly applied at point B in the direction from B towardC.Remove the torque.The steel and brass are assumed to have Poisson’s ratios of 0.30. (a)Determine the internalforce in AB.(b)Determine the internal force in BC.(c)Determine the deflection at Point B.(d)Determine thereaction at Point A.(e)Determine the reaction at Point C. Explain your work concisely and in detail
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 9600 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 2800 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 62 in., b = 22 in., and c = 24 in.
Unit load method for deflection of pin jointed frames
A simply supported beam has loads P1-38 kN, P2-68 kN, and P3-74 kN. Calculate the deflection at C in terms of El. Note: If the deflection is downwards, answer in a negative value, otherwise, answer in positive value. (i.e. 562.50/EI should be answered -562.5) Answer in 2 decimal places P, (kN) P2 (kN) P3 (kN) 2.4m 3.2m 3.8m A В C D E 12.8m
Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi
#2 will upvote anyone who will answer
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11000 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 3300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 22 in., and c = 32 in.
The 80 mm diameter shaft is made of 6061-T6 Aluminum having an allowable shear stress of τallow = 60 MPa. Find the maximum allowable torque T. Also, find the corresponding angle of twist of disk A relative to disk C.