Answered: A large pump is capable of creating a…

Name: A large pump is capable of creating a gauge pressure of 54,687 Pa. Wh
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: A large pump is capable of creating a gauge pressure of 54,687 Pa. What is the highest point it is able to pump water to?A Moving to another question will save this response.

Science

Physics

A large pump is capable of creating a gauge pressure of 54,687 Pa. What is the highest point it is able to pump water to?

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter11: Fluid Statics

Section: Chapter Questions

Problem 79PE: (a) How high will water rise in a glass capillary tube with a 0.500-mm radius? (b) How much...

See similar textbooks

Similar questions

(a) How high will water rise in a glass capillary tube with a 0.500-mm radius? (b) How much gravitational potential energy does the water gain? (c) Discuss possible sources of this energy.
A tank in the shape of an inverted cone has a height of 15 meters and base radius of 4 meters and is filled with water to the depth of 12 meters. What is the amount of work needed to pump all the water to the top of the tank? a. 6.7 × 106 N O b. 4.8 x 106 N O c. 7.5 x 106 N O d. 5.4 x 106 N e. None of the choices.
Water flows at 1 m/s from a hot water heater, through a 45o kPa pressure regulator. The pressure in the pipe supplying an upstairs bathtub 5 m above the heater is 350 kPa. Whats the speed in this upstairs pipe? Answer in M/s
A tank in the shape of an inverted frustum of a cylinder with diameters 4 ft and 6 ft and 4 ft deep, is full of water. Find the work required to pump the water out of the tank, leaving I foot depth of water at the bottom. Density of water is 62.4 lbs/ft 3. See the figure. -5 -4 -3 6 5 4 -3 2 1- 0 -1- 3 4 5
A hydraulic lift is used to lift a car that weighs 1200 kg. The foot pedal is attached to a piston that has an area of 80 cm2. This is attached to a lift with a large piston with an area of 3500 cm2. What force needs to be applied to the small piston in order to lift the car? ? N How far will the smaller piston need to be pushed in order to raise the car by 2 meters? ? m
For its drinking water, a small cabin in the woods uses a sealed water tank. The tank is filled to a depth of 1.89 m and then a small air pump can be used to pressurize the pocket of air above the water. Water flows out from the bottom of the tank through a small hole. What is the speed of water when it exits the tank if the air is pressurized to a gauge pressure of 2.05 atm? Give your answer in units of m/s.
Two pistons push down on the fluid filling two cylinders connected by a narrow hose, as shown in the figure. The area A1is 1 square inch, and the area A2 is 10 square inches. A force of 4 pounds is exerted downward on piston 1, as shown. The pressure on A1 in psi is a. 0.25 b. 0.4 c. 4 d. 10 e. 40 The pressure on A2 in psi is a. 0.25 b. 0.4 c. 4 d. 10 e. 40
The vat shown in the accompanying figure contains water to a depth of xo 1.3 m. Find the work required to pump all the water to the top of the vat. Use 9810 N/m³ as the weight density of water. NOTE: Enter the exact answer. GIRIMARI. Work Mon 3 m 6 m 4 m
A fuel oil tank is an upright cylinder, buried so that its circular top is 10 feet beneath ground level. The tank has a radius of 8 feet and is 24 feet high, although the current oil level is only 16 feet deep. Calculate the work required to pump all of the oil to the surface. Oil weighs 50lb/ft^3 I got the answer Work= 1331200pi lb-ft My answer is wrong including the units. I don’t know what they want.
3.5 A pipe 50 cm in diameter carries water (10°C) at a rate of 0.5 m/s. A pump in the pipe is used to move the water from an elevation of 30 m to 40 m. The pressure at section 1 is 70 kPa gage and the pressure at section 2 is 350 kPa gage. What power in kilowatts and in horsepower must be supplied to the flow by the pump? Assume h, = 3 m of water and - a, = 1. %3D %3D a,
A water trough has a semicircular cross section with a radius of 0.3 m and a length of 1 m (see figure). a. How much work is required to pump the water out of the trough (to the level at the top of the trough) when it is full? Use 1000 kg/m³ for the density of water and 9.8 m/s² for the acceleration due to gravity. b. If the length is doubled, is the required work doubled? Explain. c. If the radius is doubled, is the required work doubled? Explain. 1 m 0.3 m
a covid patient in ICU is injected with IV intravenous fluid. The IV flows from a raised bottle into an inserted needle. The IV bottle is slowly raised until the excess pressure from bottle height is 5kPa. The bottle needs to be cm above the injectionI need help with this. How do I figure it out