A ladder leans against a wall at an angle 0 above the horizontal as shown in figure. The ladder is uniform with mass M and length L. Assume that the ladder is at rest due to friction between the ladder and ground. What i the torque exerted by gravity on the ladder about the axis of rotation shown (horizontal and parallel to the wal axis through its base)? (A) zero (B) Mg cos 0 (C) MgL (D) MgL cos 0 (E) M9L sin e F) MgL 5) Mg sin 0 ) One needs the coefficient of friction to answer this problem

A ladder leans against a wall at an angle 0 above the horizontal as shown in figure. The ladder is uniform with mass M and length L. Assume that the ladder is at rest due to friction between the ladder and ground. What i the torque exerted by gravity on the ladder about the axis of rotation shown (horizontal and parallel to the wal axis through its base)? (A) zero (B) Mg cos 0 (C) MgL (D) MgL cos 0 (E) M9L sin e F) MgL 5) Mg sin 0 ) One needs the coefficient of friction to answer this problem

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The figure shows a jet engine suspended beneath the wing of an airplane. The weight of the engine is 10100 N and acts ash shown in the figure. In flight the engine produces a thrust of 64500 N that is parallel to the ground. The rotational axis in the figure is perpendicular to the plane of the paper. With respect tot he axis, find the magnitude of the torque due to (a) the weight and (b) the thrust.
O Rësources Lx Give Up? Hint The wheels of a wagon can be approximated as the combination of a thin outer hoop, of radius r = 0.262 m and mass 4.32 kg, and two thin crossed rods of mass 8.66 kg each.A farmer would like to replace his wheels with uniform disks ta = 0.0588 m thick, made out of a material with a density of 8290 kg per cubic meter. If the new wheel is to have the same moment of inertia about its center as the old wheel about its center, what should the radius of the disk be? ra = about us privacy policy contact us help careers terms of use
F y mg f.Y Frxe f,x Axis The ladder in the picture has a mass of 32 kilograms and a length 3.2 meters. What is the normal force pushing the ladder up from the floor? FN = Assume that the ladder's weight is evenly distributed, so it can be treated as a single force through the middle. If the ladder is at a 60° angle from the ground, what is the torque exerted by the weight (using the floor as the pivot point)?
A uniform, thin, solid door has height 2.35 m, width 0.855 m, and mass 25.0 kg. (a) Find its moment of inertia for rotation on its hinges. kg · m2 (b) Is any piece of data unnecessary? (Select all that apply.) The height of the door is unnecessary. O The width of the door is unnecessary. O The mass of the door is unnecessary. O No; all of the data is necessary.
A bicycle wheel can be thought of a uniform hoop with a radius of 48 cm and mass 1.6 kg. Consider the case where the wheel start from rest and accelerates uniformly under the action of a constantly applied torque of 0.5 N-m exerted by a force at the edge of the wheel. The torque is caused by the bicycle chain acting at a radius of 11.5 cm from the center of the wheel. (a) How long does the wheel take to reach a speed of 10 rev/min? (b) Through how many revolutions does it turn while accelerating? Your Answer: Answer
Calculate the net torque about point O for the three forces (F₁=15.7 N, F₂=17.8 N and F3-20 N) applied on the rod as shown in the figure, where =25.2°. The rod and all forces are in the plane of the page. Assume the z-axis to be the axis perpendicular to the page. -12.0 m- 13.00 m 90.0⁰ 00 F₁ -4.00m- F2 10.3 m.N, about the z-axis 147 m.N, about the z-axis -66.5 m-N, about the z-axis 308 m.N, about the z-axis F3
plss answer correctly
Don't use chat gpt It Chatgpt means downvote
A force, T, is exerted on a horizontal beam at point B at an angle 8 with respect to the horizontal as shown. The magnitude of the torque created by force T about point C, is given by E A AT B W₁ O W₁
Force F = (5.58 N)î – (6.71 N )k acts on a pebble with position vector 7 = (2.79 m ) – (7.59 m ) k, relative to the origin. - What is the resulting torque acting on the pebble about (a) the origin and (b) a point with coordinates (3.43 m, 0, -3.30 m)? (a) Number i i k Units (b) Number i i i k Units
A 2.0 m long, 200 N uniform ladder, rests with one end against a smooth wall making an angle of 30° with the wall. The coefficient of static friction between the ground and the lower end of the ladder is 0.5. A force F pushes the upper end of the ladder parallel to the wall so that the ladder is on the verge of starting to slip down (static friction has reached its maximum value). The torque of the weight of the ladder relative to the lower end in the ground is: a. 200 Nm b. 620 Nm C. 546 Nm d. 400 Nm e. None of the above I
A simple pendulum consists of a small object of mass 3.0 kg hanging at the end of a 2.0-m-long light string that is connected to a pivot point. (a) Calculate the magnitude of the torque (due to the force of gravity) about this pivot point when the string makes a 8.0° angle with the vertical. N.m (b) Does the torque increase or decrease as the angle increase? increase O decrease Explain.