Related questions
Question
Transcribed Image Text:A jet of water flows from left to right and hits a splitter block,
as shown in the figure. Some of the jet is diverted upwards
and some of it downwards. The incoming jet has a velocity
= 2.7 m/s and a cross-sectional area A₁.
U₁
=
The jet that is deflected upwards has a velocity U₂ = 0.6
m/s, a cross-sectional area A2
5 cm² and is at an angle
=
02
20° with respect to the horizontal.
=
The jet that is deflected downwards has a velocity U3
0.8 m/s, a cross-sectional area A3 = 7 cm² and is at an
angle 03 35° with respect to the horizontal.
The density of water is p = 1000 kg/m³.
U₁
=
A₁
A₂
U₂
Өг
3
=
Transcribed Image Text:C)
What
The vertical force on the block is found to be Fy.
velocity of the incoming jet (i.e. what value of u₁) would
be needed to generate a force of 4Fy?
(Note that you don't need to actually find Fy to solve this
question!)
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 3 steps
Knowledge Booster
Similar questions
- The settling rate of particulates in the air follows Stokes' law. If particulates of diameter of 10 nm emitted in the atmosphere are found to settle out after 2 days, how long would it take particulates of the same material with a diameter of 5 nm to settle out if they are emitted from the same source?arrow_forwardWater moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is 1.85 ✕ 105 Pa and the pipe radius is 2.70 cm. At the higher point located at y = 2.50 m, the pressure is 1.27 ✕ 105 Pa and the pipe radius is 1.30 cm. A pipe is open at both its left and right ends. The pipe starts at the left end, extends horizontally to the right, curves up and to the right, and extends horizontally to the right again. The right end is higher than its left end, and the change in height is labeled y. The diameter at the right end is smaller than the diameter at the left end. The pressure at the left end is labeled P1, and the pressure at the right end is labeled P2. (a) Find the speed of flow in the lower section. m/s(b) Find the speed of flow in the upper section. m/s(c) Find the volume flow rate through the pipe. m3/sarrow_forwardThe lower section of a constricted pipe has a diameter of 8 cm. The upper section of the pipe, located 0.1 m above the lower section, has a diameter of 3 cm. The pressure at the lower section is 2.1 ×× 104 Pa, while the pressure in the upper section is 1 ×× 104 Pa. Assuming water moves through the pipe in a steady flow, calculate the speed (in m s-1) of the flow in the lower section. The density of water is 1000 kg m-3.arrow_forward
- Solvearrow_forwardA firefighter mounts the nozzle of his fire hose a distance 32.1 m away from the edge of a burning building so that it sprays from ground level at a 45° angle above the horizontal. After quenching a hotspot at a height of 9.33 m, the firefighter adjusts the nozzle diameter so that the water hits the building at a height of 17.5 m. By what factor was the nozzle diameter changed? Assume that the flow rate of water through the hose stays the same, and treat the water as an ideal fluid. factor by which the hose diameter changed:arrow_forwardA rectangular solid made of aluminum has a density p= 2.70 g/cm³. The dimensions of the solid are shown below. The solid is placed on top of a truncated cone whose circular ends have the dimensions shown. The bottom of the rectangular solid down on the top surface of the cone. Find the pressure (in N/m²)between those two surfaces. (Ignore air pressure.) (1 kg = 1000 g, 1 m 100 cm) presses 10.0 cm 8.00 cm 15.0 cm r= 2.00 cm R = 6.00 cmarrow_forward
- 9-90. The starter for an electric motor is a full cylinder and has the cross-sectional areas shown. If copper wiring has a density of Peu = 8.90 Mg/m³ and the steel frame has a density of Pst = 7.80 Mg/m³, estimate the total mass of the starter. Neglect the size of the copper wire. Problem 9-90 Steel Copper 80 mm 50 mm 30 mm 100 mm 60 mmarrow_forwardThe lower section of a constricted pipe has a diameter of 8 cm. The upper section of the pipe, located 0.1 m above the lower section, has a diameter of 3 cm. The pressure at the lower section is 2.1 ×× 104 Pa, while the pressure in the upper section is 1 ×× 104 Pa. Assuming water moves through the pipe in a steady flow, calculate the speed (in m s-1) of the flow in the lower section. The density of water is 1000 kg m-3arrow_forwardCalculate the Reynolds numbers for the flow of water through a nozzle with a radius of 0.270 cm and a garden hose with a radius of 0.940 cm, when the nozzle is attached to the hose. The flow rate through hose and nozzle is 0.485 L/s. (Assume the temperature of the water is 20°C.) (a) a nozzle with a radius of 0.270 cm Can the flow possibly be laminar? Yes No (b) a garden hose with a radius of 0.940 cm Can the flow possibly be laminar? Yes Noarrow_forward
- Assume that a raindrop has a volume of 0.05 cm^3 and you need an Avogadro's number of raindrops to fill up the cubic water tank. What is the length of the edge of the tank?arrow_forwardA gunpowder explosion in a cannon reaches a gas pressure of 3.0E8 Pa. If the cross sectional area of cannonball is 75 cm^2 what force is appliedarrow_forwardOil (p = 920 kg/m³) is flowing through a pipeline at a speed of 1.88 m/s. If the diameter of the pipe is 0.16 m, what is the %3D mass flow rate? kg/sarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios