A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M)

A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M)

Name: A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Int
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

A multifluid container is connected to a U-tube, as shown in the figure. For the given specific gravitles and fluid column heights. determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at A. The column heighth of oil is 86 cm. The specific gravitles are 1.26 for glycerin and 0.90 for oll. We take the standard density of water to be Pw=1000 kg/m³ and the specific gravity of mercury to be 13.6. h 35 cm 18 cm Į Oil SG-0.90 Water Glycerin SG-1.26 90 cm 15 cm The gage pressure at A is kPa. The height of a mercury column that would create the same pressure at A is cm.
Step by Step Determine the distance that the column of fluid will rise in a 1-cm open tube when the tube is inserted in fluid with a density of 990 kg/m^3 and a surface tension of 0.09 N/m. Provide answer in cm and assume a contact angle of 0-degree.
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
A 80 cm tall cylinder is filled with water (ρwater = 1000 kg/m3) and oil (ρoil = 600 kg/m3) and is capped on the bottom so no fluid is flowing. It contains equal amounts of the two fluids by weight. What is the pressure at the bottom of the cup?
I.A U-tube manometer filled with Liquid A is attached to the underside of 4 inch pipe carying water, as shown in Figure 2. At a point directly above the inclined U-tube manometer tap, the upstream tap of an inverted U tube is located. The inverted-U-tube manometer is filled with a Liquid B. If the P:-17 psi, determine; (Note: I in (inch) - 25.4 mn, I atm - 101.325 kNiw - LO1325 har - 101.325 APa - 14.7 poi, g -9.8sims) (a) the differential manometer reading (psig), and (b) the value of X (inch). Liquid , SG-05 12 in. Water Liquid A, SG 16
The left limb of a U-tube mercury manometer isconnected to a water pipe line, with the mercury level inthe leg (specific gravity = 13.6) 19.685inches below thepipe line's center, and the right limb open to theatmosphere. The right limb's mercury level is 0.4374 yardhigher than the left, while the space above mercury in theright limb contains benzene (specific gravity = 0.88) to aheight of 0.2 m. Determine the water pressure in the pipe.
A cylinder glass tubing is 4.4ft long with one end closed and is immersed vertically with the open end down into a tank of cleaning solvent (S.G = 0.83) until only 4.8 inches of it remains above the liquid surface. Determine the fluid rise inside the tube. (Patm = 14.7 psi) Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: in Decimal Places required in the final answer: 2
A tube with diameter of 0.3cm is inserted into water (Surface tension= 0.061N/m). The water in the tube rises to a height of 0.45cm from the surface. Calculate the contact angle between the water and the tube.
A container is filled with oil. A pipe is connected to the container at point C and the owner left the cover open, exposing the oil to the atmospheric pressure at point B and point E. What will be the maximum absolute pressure (psi) using the height of the oil from the previous problem. The density of the oil used is = 1.78 slug/ft^3*
Include a free body diagram A simple manometer is used to measure pressure of oil (s= 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and the left limb is connected to the pipe. The cente of the pipe is 9 cm below the level of mercury (s=13.6) in the right limb. If the difference of mercury level in the two limbs is 15 cm, determine the absolute pressure of the oil in the pipe in kPa. a. 278.6 b. 25.11 c. 64.74 d. 120.58
What will be the gauge pressure and absolute pressure of water at a depth 12m below the surface? Take Pwater = 1000 kg/m³ and P = 101 kN/m2 atm
A 75−mm-diameter pipe, 2-m-long is just filled with oil (SG=0.822) and then capped. It is placed in a horizontal position and then rotated at 27.50 rad/sec about a vertical axis 0.50m from one end. Determine the following: (a) pressure at the far end of the pipe (b) pressure at the near end of the pipe (c) pressure at the midpoint of the pipe.