A homogenous 800 kg. bar AB is supported at either end by a cable shown in the figure below. Calculate the smallest area of each cable if the stress is not to exceed 90MPa in bronze and 120 MPa in steel A Bronze L = 4 m 10 m A Area of steel = 32.77 sq.mm, Area of Bronze = 43.66 sq.mm B Area of bronze = 32.77 sq.mm, Area of steel = 43.66 sq.mm Area of steel = 6.4594 sq.mm, Area of bronze = 7.4558 sq.mm Area of bronze = 6.4594 sq.mm, Area of steel = 7.4558 sq.mm Steel L=3m B

A homogenous 800 kg. bar AB is supported at either end by a cable shown in the figure below. Calculate the smallest area of each cable if the stress is not to exceed 90MPa in bronze and 120 MPa in steel A Bronze L = 4 m 10 m A Area of steel = 32.77 sq.mm, Area of Bronze = 43.66 sq.mm B Area of bronze = 32.77 sq.mm, Area of steel = 43.66 sq.mm Area of steel = 6.4594 sq.mm, Area of bronze = 7.4558 sq.mm Area of bronze = 6.4594 sq.mm, Area of steel = 7.4558 sq.mm Steel L=3m B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C NANTSELEINE Steel: A = 900 mm² E = 200 GPa L=1.5m Bronze: A=1200 mm² E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? O 0.367 O 0.433 O 0.467 0.333
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by the straight line segment shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is E max = 0.05. 630 560 420 (MPa) 0.006 0.025 0.05 100mm M € (mm/mm) 75mm
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. a b C Steel: A-900 mm E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 0.467 0.333
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. b C P Steel: A = 900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0m E= 200 GPa L = 1.5m What is the value of P without exceeding the allowable stress of steel, in kN? 250 340 280 O230
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
H.W.1: A steel bar 6 m long is 5 cm in diameter for 3m of its length and 2.5 cm in diameter for the second 3m as shown in Figure below. The smallest diameter part of the bar is with 11 N/mm2 tensile stress due to the applied load. Find the final diameters of the two parts after the applied load. E for the steel is 200x10 N/mm and u of the steel is 0.28. P 3 m 3 m
3. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? 2 m -- -1.5 m- 1.5 m 10 Steel A=900 mm2 E=200 GPa L=15 m Bronze A=300 mm2 E= 83 GPa L3D2 m
The light rigid bar ABCD shown in the × figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free and load P = 20 kips is applied. 4 ft Aluminum L = 4ft A = 0.75 in² E = 10 x 106 psi Steel L = 3ft A = 0.5 in² E = 29 x 106 psi k2A2A A. What is the stress experienced by aluminum rod B. What is the stress experienced by steel rod. C. What is the resulting deformation on the aluminum rod.
Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft
5. The rigid bar of negligible weight is supported as shown in figure 5. If W = 80 kN. compute the temperature change of the assembly that will causata tensile stress of 50 MPa in the steel rod. Use the following data: A (mm2) 300 1400 a (C) 11.7x 10+ 18.9x 104 E (GPa) 200 Steel Rod Bronze Rod 83 Figure 5 Bronze 3 m Steei 1.5 m 1.0 m 1.5 m 2.5 m 目