A homogeneous rod of constant cross section has length of 6 m and weighs 2500 N. The rod is resting on smooth surfaces at A and B. A cable CD is holding the rod in the position shown. Determine the following: a) Reaction on the floor. b) Reaction on the wall. c) Tension in the cable. A 4m B D 1m 3m

A homogeneous rod of constant cross section has length of 6 m and weighs 2500 N. The rod is resting on smooth surfaces at A and B. A cable CD is holding the rod in the position shown. Determine the following: a) Reaction on the floor. b) Reaction on the wall. c) Tension in the cable. A 4m B D 1m 3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 1 Determine the reaction at A and C. Support at A is fixed, C is roller support, and B is…

Q: -9 m 6 m- A 12.25 m a C B 60 kg/m

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A: Given TAB= 110 lb

Q: The system shown has a pin at A and a roller at B. If the force, F = 55 lb, height = 6.7 ft, and…

Q: Draw the influence line for member BC and interpret the diagram.

A: Solution: Considering the diagram of Truss: Applying a unit load at x from point A and find the…

Q: L2 La L, D Ls F Bar AB is supported by pin A and cable BC. Find the reactions at support A and the…

A: Reaction: The force or the moment which are exerted on a body due to its supports are called…

Q: reactions using S DM Solve for the suupport s0kw/m A EI constant 4m am 3m

Q: determine (a) the tension in the cable, (b) the reaction at C.

Q: DY *5-72. Determine the components of reaction at the ball- and-socket joint A and the tension in…

Q: A cable is used as a laundry washing line whose end points are fixed at A and B. The clothes on the…

Q: The reaction at the support D of the continuous beam ABCD, hinged at two points shown in below…

Q: ecause the cable passes over a small pulley at B, the tension may be as he cable. Assume a = 3 in. A…

Q: In the Figure shown, calculate the mass of the cylinder is 200 kg and that of member AB is 50 kg.…

Q: The reaction at the support D of the continuous beam ABCD

Q: The dead load on the bridge girder is 800 N/m and the live load is shown below. Assume B and D are…

A: Given data: Dead load on the bridge girder=800 N/m Series of point live loads are moving on girder…

Q: A 20 m steel tape was standardised on flat ground, at a temperture of 20 C° and under a pull of 15…

A: Given data: L=20mTo=20°CPo=15KgTm=30°CPm=10KgA=0.22 cm2E=2.1×106Kg/cm2α=11×10-6 /°CW=400g=0.4 Kg

Q: QUESTION 5 A light uniform rod OAB is held by a ball-and-socket joint at O and supported by cable…

A: From the given question it is required to Determine the tension in the cable and reaction at ball…

Q: Draw the influence line for member BC and interpret the diagram. Show complete solution and figures.…

Q: A) The spring AB has a stiffness of k=800 N/m and an unstretched length of 200 mm. Determine the…

Q: Draw the influence line for member BC and interpret the diagram. F H 15 ft A E 4 @ 20 ft = 80 ft-

Q: Determinate the horizontal and vertical components of reactions at the pin connections at A, B, and…

Q: The uniform rod in the figure shown weighs 500kN and has its center of gravity at G. Determine the…

A: The uniform rod is given as To find:- Tension in cable Reactions at A and B Concept:- A free body…

Q: 6- The rectangular gat has dimensions 6 m by 2 m. Neglect the weight of the gate. Determine (a) The…

Q: Homework 1 Q1) The frame shown below supports 100lb weight. The cable is attached at A and passes…

Q: Consider the structure shown below. Determine the tension in the cable and the horizontal and…

A: Given: Weight of cylinder = 80lb

Q: The homogeneous bar shown is supported by a smooth pin at C and a cable that runs from A to B around…

Q: 10k IB 5' 5' in

A: Solution:- Support reactions at A and B, Ra+Rb=2×10+10 =30 k Taking moment about B,…

Q: b.) Using the value for F1,min that you calculated in (a), replace the two forces F₁ and F2 with a…

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A: Total length = 5+4+7+3 = 19

Q: The reaction at the support D of the continuous beam ABCD, hinged at two points shown in below…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: P=5.2KN

Q: Q2. (а) A beam is supported and loaded as shown in Figure Q2(a). Point A is a M UTM pin support and…

Q: Given the frame below. Find the Reaction at C and Tension of the cable. If W = 100 N. Note: (Neglect…

A: W=100N To find reaction at C and tension in cable

Q: If the load has a weight of 200 lb, determine the x, y, components of reaction at the…

A: Given : Weight = 200 lb Determine x, y and z component of reaction at the ball and socket joint A…

Q: The two loads are suspended from the ABCD cable as shown. dC = Since it is known to be 2 m, the…

A: ##Calculate the reaction at support D And It's Components At D of cable ABCD Since bending moment…

Q: Q2. the the pin A. The pulley at D is frictionless and the cylinder weighs W lb. See the values of W…

A: Draw the free body diagram.

Q: The reaction at the support D of the continuous beam ABCD, hing

Q: a connections, calculate the pin rea . Usea pin diameter of 16 mm in a

Q: 2) An 8m bar hinged at the left end carries a 100N load 5m from the hinge support. The bar is also…

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

A homogeneous rod of constant cross section has length of 6 m and
weighs 2500 N. The rod is resting on smooth surfaces at A and B. A
cable CD is holding the rod in the position shown. Determine the
following:
a) Reaction on the floor. b) Reaction on the wall.
c) Tension in the cable.
A
C
4m
B
D
1m
3m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the system shown; F1 = 20kN, F2 = 10kN, F3 = 10kN (in the middle of the DCBF plane and in the vertical direction),M1 = 20kNm (valid for OHDC plane), M2 = 10kNm (valid for OHGA plane). According to this;a) Find the velocity of the force F2 on the OD axis as a vector.b) Reduce the given system of forces to point O.c) Can we reduce the system of given forces to a single force?
Cable ACB supports a load uniformly distributed along the horizontal as shown. The lowest point C is located 9m to the right of A. Find the maximum tension at A in Newton and minimum tension in Newton
The light right-angle boom which supports the 360-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. A Ox - Answers: IM TAC = i Me C 0.65 m y 1.05 m! 0.65 m 10 B 360 kg 1.30 m 2.30 m N Oy E 1.45 m II D N TBD = 1.45 m Hr x N O₂ = Mi N TBE = i N N
IHE BARS AB AND AC ARE JÕINED BY A PIN AT A AND A HORIZONTAL CABLE. THE VERTICAL CABLE CARRYING THE 200-kg MASS IS ATTACHED TO THE PIN AT A. DETERMINE THE TENSION IN THE HORIZONTAL CABLE. NEGLECT THE WEIGHTS OF THE BARS. 30° 60° 3 m 2 m B 200 kg
The homogeneous bar AB weighs 550 N. End B lean against a rough vertical surface and end A is supported by a ball-and-socket joint. Determine the reaction at A and B of the tension in the cable is 150 N. Z. C 30° В 5 m 6 m --- 4 m X A y
The tube supports the four parallel forces. Determine the magnitudes of forces FC and FD acting at C and D so that the equivalent resultant force of the force system acts through the midpoint O of the tube.
A
From the moment diagram shown, assuming there are no variable loadsa. What is the value of the reaction at B.b. What is the value of the load from A to B?c. What is the value of the load from B to C?
frame2 Given the Frame as shown below with weight ‘W’ for the smallermember and weight ‘2W’ for the larger member. Assume θ = 60°. Using Methodof Members, determine the following:a.) The External Reaction at Point A in terms of W.b.) The Internal Reaction at Point B in terms of W.c.) The External Reaction at Point C in terms of W.d.) The Tension at Point D in terms of W.
The bars AB and AC are joined by a pin at A and a horizontal cable. The vertical cable carrying the 200-kg mass is attached to the pin at A. Determine the tension in the horizontal cable. Neglect the weights of the bars 200 kg Answer: 1416 N
Can you please show the steps on how to solve this problem. I want to be able to follow along
If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the support reactions in point O.. X 3 m 1.5 m 1.5 m 3 m. B 1 m