A home is heated with propane with a 100,000 BTU furnace size and 95% efficiency. The monthly heating degree days is 5000. Using the energy estimation discussed in this chapter, estimate the monthly and annual gas consumption to heat the building if the home is to be kep 68°F.

A home is heated with propane with a 100,000 BTU furnace size and 95% efficiency. The monthly heating degree days is 5000. Using the energy estimation discussed in this chapter, estimate the monthly and annual gas consumption to heat the building if the home is to be kep 68°F.

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter8: Direct Use Of Solar Energy

Section: Chapter Questions

Problem 6P

See similar textbooks

Related questions

Q: A 1 lbm/s fluid enters a machine at 170 m/s. 800 kPa, and with a specific volume of 0.3 m³/kg. The…

A: Determine workdone by the fluid?

Q: A cylinder that contains 0.068 kg of carbon dioxide (with molar mass 44 kg/kmol), occupying a volume…

A: A temperature is a unit of the average kinetic energy of the particles in an particle. When…

Q: An electric heater supplies (R+2.5)kW of power in the from of heat to water. If in 5.5 hours, 350kg…

A: Given data- Power (P) = (R+2.5)kW=(83+2.5)kW=85.5kW Time (t) = 5.5 hours Mass of water (m) = 350kg…

Q: A 600 MW coal-fired power plant has an overall thermal efficiency of 38%. It is burning coal that…

A: Given data: Capacity of the coal-fired power plant = 600 MW Overall thermal efficiency = 38% Heating…

Q: Water falls from a height of 500 m and the mass of water is 50 kg. What is approximately the rise in…

Q: Find the energy required to increase the room temperature of a coffee in a cup to a temperature of…

A: A type of elastic collision in which two objects of equal mass initially move in the same direction…

Q: Calculate the evaporation rate from an open water source, if the net radiation is 300 W/m and the…

Q: Consider a house that is approximated as a cube that is 8 m on a side and has no windows. The house…

A: Given: Each side of house=8 m Inside temperature=20°C Outside temperature=-20°C Total heat loss per…

Q: You plan to perform a tiered LCA of a microwave. An environmentally extended economic input-output…

Q: The ionization constant for water (Kw) is 9.311 × 10−14 at 60 °C. Calculate [H3O+], [OH−], pH, and…

A: Given: The ionization constant for water (Kw) is 9.311 × 10−14 at 60 °C. On Calculating the value…

Q: The R- value for a 50 mm wood fiber insulation board (k= 0.044 W/m.K)=…

A: Note:- As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly…

Q: A domestic refrigerator is loaded with food and the door closed. During a certain period the machine…

A: The first law of thermodynamics explains that energy can neither be created nor destroyed. heat is…

Q: A certain brand of hotdog cooker works by applying a potential difference of 146 V across opposite…

A: Given data; Potential difference, V=146 V Current, i=12.8 A H=60.8 KJ

Q: Calculate the specific energy of 13 m3/s of water flowing with a velocity of 1.5 m/s in a…

A: Discharge, Q=13m3sec width of rectangular channel=7.5 m velocity of channel=1.5msec Now we know…

Q: In a refrigeration cycle that is used to cool products of a grocery store has an efficiency of 46 %.…

Q: A 60 MW steam power station has a thermal efficiency of 30%. If the coal burnt has a calorific value…

A: Given: The steam power is 60 MW. The thermal efficiency is 30%. The calorific value of the coal is…

Q: Which emits more SOx per unit amount of electricity produced; a coal-fired plant with a 90%…

A: Given data Efficiency, η=0.9 heating value of coal=13,000 Btu/lb heating value of oil=6×106…

Q: 1. What is energy per unit head of water called as a) Total energy b) Specific energy c) Velocity…

A: Energy per unit head of water

Q: The contents of a tank are to be mixed with a turbine impeller that has six flat blades. The…

Q: A cylindrical tank 3m long and 4m diameter is used for oil storage. How many days can the tank…

Q: The Energy Efficiency Rating (EER) of an air-conditioning unit is defined asthe ratio of the heat…

A: Given; The amount of heat removed is 5,170 Btu. The power of unit is 470 watts. The Energy Efficient…

Q: 6.0 g of cream at 13.2 °C are added to an insulated cup containing 150.0 g of coffee at 92.9 °C.…

Q: Calculate the power radiated by a woodstove of dimensions 65 cm high by 55 cm deep by 85 cm wide…

A: Data given: Dimensions: Height (H) = 65 cm Depth (D) = 55 cm Width (W)= 85 cm Surface temperature =…

Q: For a building located in London, England with annual heating degree-days (dd) of 5634, a heating…

Q: The enthalpy of combustion of benzoic acid (C6 H5 COOH) is commonly used as the standard for…

A: Some compounds release more energy than others in combustion reactions. Combustion enthalpy can be…

Q: Idea of Ocean thermal energy was given in 1981. Select one: True False

A: Ocean Thermal Energy It is the use of the temperature difference between deep ocean water and warm…

Q: Bananas are to be cooled from 29.7°Cto 6.9°C at a rate of 1464 kg/h by refrigerator that operates on…

A: Given data Initial temperature of bananas T1 = 29.7 o C Final temperature of bananas T2 =6.9o C Mass…

Q: On a hot summer day, the flat roof of a tall building reaches 50° C in temperature. The area of the…

A: The rate of heat energy radiation (R) Joule/sec/m2 or watt/m2 Depends upon certain parameters, they…

Q: A stove element draws 15 A when connected to a 240-V line. How long does it take to consume 60 kJ .

A: Given: The current is 15 A. The voltage line is 240 V. The energy is 60 kJ.

Q: calculate the heat loss through the ceiling, if the R-19 insulation batt is replaced by R-40…

A: To find:- heat loss through ceiling if R-19 insulation batt is replaced by R-40 fiberglass…

Q: A domestic refrigerator is loaded with food and the door closed. During a certain period the machine…

A: Given:- The energy consumed by the machine for a certain period = 5 kWh The internal energy of the…

Q: The annual average insolation for a fixed solar panel in city A is 350 W/m?. On the other hand, city…

A: Given,efficiency of panel for each city=17%For city A,Annual average electricity=13000…

Q: Steven installed a new solar system on his roof. Calculate the watt capacity of his system and the…

Q: power (in kW) recovered in the turbine

A: Given:' Density of water= 9810 N/m3 = 1000.34 kg/m3 g = 10 m/s2 Efficiency of turbine and pump = 70%…

Q: Assume that gasoline is burned with 99% efficiency in a car engine, with 1% remaining unbumed in the…

A: Given:- efficiency=99% remaining =1% engine =16 kg MW=30 MW=100 To find:- fraction of VOCs

Q: For a building located in Madrid, Spain with annual heating degree-days (dd) of 4654, a heating load…

A: Given:- annual heating degree-days (dd) of 4654, a heating load (heat loss) of 30,000 kj/h, and a…

Q: A small electric immersion heater is used to heat 71 g of water for a cup of instant coffee. The…

A: The given data is as follows: Mass of water=71 gPower=63 wattsInitial temperature=19∘CFinal…

Q: Qs 23). Decane is a liquid with density of 730 kg/m3 and a lower heating value of 44.24 MJ/kg. If…

A: Answer 23. Given data: The decay density is 730 kg/m3. The lower heating value is 44.24 MJ/kg. The…

Q: A heat source of unknown temperature supplies energy of (R+650)kJ to a carnot heat engine. If this…

A: Consider the free body diagram;

Q: Which end use is largest consumer of energy in Canadian commercial buildings? Water heating Space…

A: The end use electricity usage is highest water heating and space heating. But largest among these 2…

Q: The data is related to a pelton wheel as follows: Head at the base of the nozzle: 80 m Diameter of…

Q: Replacing incandescent lights with energy-efficient fluorescent lights can reduce the lighting…

A: Given data:

Q: List down three to five situations in which buildings, roads or other structures has been built to…

A: Any substance that may be utilised for construction is referred to as a building material. Wood,…

Q: Water flows from a large reservoir through a pipe system which consists of 200 mm diameter of pipe…

A: The velocity is the water moving in the pipe with particular time is said to be velocity. writing…

Concept explainers

Temperature as a Fundamental Dimension

There are certain rules to write dimensions of a physical quantity using the fundamental dimensions. They are outlined below.

Question

A home is heated with propane with a
100,000 BTU furnace size and 95%
efficiency. The monthly heating degree
days is 5000. Using the energy estimation
discussed in this chapter, estimate the
monthly and annual gas consumption to
heat the building if the home is to be kept
68°F.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

To maintain a dwelling steadily at 68°F on a day when the outside temperature is 40°F, heating must be provided at an average rate of 300 Btu/min. Determine the electrical power required, in kW, to deliver the heating using: (a) electrical-resistance heating, (b) a heat pump whose coefficient of performance is 3.5, (c) a reversible heat pump operating between hot and cold reservoirs at 68°F and 40°F, respectively. Part A Determine the electrical power required, in kW, to deliver the heating using electrical-resistance heating. W₁ = i kW
conversion: Given 200 ppmv SO2 (@STP), what isthe SO2 emission rate in lb/hr.
A spring-loaded piston-cylinder device contains 1.5 kg of carbon dioxide. This system is heated from 200 kPa and 25 °C to 1200 kPa and 300°C. Determine the total heat transfer to and work produced by this system.
As a plant maintenance engineer, you are required to purchase a 3,000 L tank of liquid butane to heat a maintenance building during the winter. You are concerned about the tank rupture and the possibility of a vapour cloud explosion of all the butane. How far (in metres) must the tank be from the maintenance building to ensure that it will receive only partial demolition in the event of an explosion? The specific gravity of liquid butane is 0.6, and the energy of explosion for butane is 510 kcal/gm-mol. Assume the explosion efficiency is 10 % in this case.
A mains fed 12000 litre tank supplies hot rinse water (45oC) for a food processing operation. Calculate the power of electric immersion heater(s) if the tank is fully replenished by 05:00 in the morning and the facility needs the hot water at 08:00.
2. Consider a "tight" 300 m3 home with o.2 ach infiltration rate. The only source of CO in the home is the gas range and the ambient concentration of CO is zero. Suppose there is no CO in the home at 6 pm, but then the oven and two burners are on for 1 hour. Assuming the air is well mixed in the house, estimate the CO concentration in the home at 7 pm and again at 10 pm.
A 50-L electrical radiator containing heating oil is placed in a 50-m³ room. Both the room and the oil in the radiator are initially at 5°C. The radiator with a rating of 3 kW is now turned on. At the same time, heat is lost from the room at an average rate of 0.3 kJ/s. After some time, the average temperature is measured to be 20°C for the air in the room, and 60°C for the oil in the radiator. Taking the density and the specific heat of the oil to be 950kg/m³ and 2.2kJ/(kg °C), respectively, determine how long the heater is kept on. Assume the room is well-sealed so that there are no air leaks.
A closed tank containing hot air has an initial internal energy of 400 kJ. During the next 5 min, the tank loses heat to the surroundings at a rate of 1.5 kW, while an electrical element supplies 1000 W to the air. Find the final internal energy of the air.
Consider a 300 m3 home with an infiltration rate of 0.2 ach, temperature of 25oC, and pressure of 1 atm. Assume carbon monoxide (CO) is a conservative pollutant, the only source of CO in the home is the gas range, and the ambient concentration of CO is always zero. Suppose there is no CO in the home at 6 PM, but then the oven and two burners are turned on for one hour. Estimate the CO concentration in the home at 7 PM and again at 10 PM (3 hours after turning off the range). Use Table 7.13 as needed Does this system exceed the 8-hr NAAQS for CO (9 ppm(v))?
The heat exchanger radiates thermal energy at the rate of 2500 kJ/h for each square meter of its surface area. Determine how many joules (J) are radiated within a 5-hour period.
For a building located in Madrid, Spain with annual heating degree-days (dd) of 4654, a heating load (heat loss) of 30,000 kj/h, and a design temperature difference of 30° C (20° C indoor), estimate the annual energy consumption. If the building is heated with a furnace with an efficiency of 92%, how muchgas is burned to keep the home at 20° C? State your assumptions.
Determining Whole-Building Ventilation Rates for Residential Buildings Whole-building ventilation replaces an amount of stale, indoor air with ventilation from the outdoors. It is intended to dilute indoor pollutants and provide acceptable air quality. ASHRAE Standard 62.2, Ventilation and Acceptable Air Quality in Low-Rise Residential Buildings, defines the roles and minimum requirements for mechanical systems, natural ventilation systems, and building envelopes intended to provide acceptable indoor air quality (IAQ) in residential buildings. We will use the following formula from ASHRAE Standard 62.2 to calculate the total required ventilation rate: Q = 0.15A floor + 3.5 (Nhr + 1) Where: Q is the total required ventilation rate (L/s) A floor is the dwelling-unit floor area (m2) Nbris the number of bedrooms (not to be less than 1) Once we know the ventilation rate in a space of a given volume, we can also calculate the steady-state CO2 concentration using the following formula: GNK…