A hollow, metal circular pipe ABC (see figure) supports a load P, = 16.6 kips acting at the top. P1 A dAB tAB P2 В Cap plate dBc tBC A second load P, = 22 kips is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are das = 1.75 in., tag = 0.5 in., dec = 2.40 in., and tec = 0.375 in., respectively. The modulus of elasticity is 10,000 ksi. When both loads are fully applied, the wall thickness of pipe segment BC increases by 200 x 10-6 in. Assume the material behaves linearly elastically. (a) Find the increase in the inner diameter of pipe segment BC (in inches). in. (b) Find Poisson's ratio for the metal. (c) Find the increase in the wall thickness of pipe segment AB (in inches). Find the increase in the inner diameter of segment AB (in inches).-

A hollow, metal circular pipe ABC (see figure) supports a load P, = 16.6 kips acting at the top. P1 A dAB tAB P2 В Cap plate dBc tBC A second load P, = 22 kips is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are das = 1.75 in., tag = 0.5 in., dec = 2.40 in., and tec = 0.375 in., respectively. The modulus of elasticity is 10,000 ksi. When both loads are fully applied, the wall thickness of pipe segment BC increases by 200 x 10-6 in. Assume the material behaves linearly elastically. (a) Find the increase in the inner diameter of pipe segment BC (in inches). in. (b) Find Poisson's ratio for the metal. (c) Find the increase in the wall thickness of pipe segment AB (in inches). Find the increase in the inner diameter of segment AB (in inches).-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kN including its self-weight which is distributed equally: a. Determine the stress on the lower washers before the buts are tightened. b. Determine the stress int the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. Determine the stress int the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. c. 44 mm Upper washer Base plate Lower washer 20 mm 22 mm 50 mm
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.500 in. and a wall thickness of 0.500 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.000-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). The bar is loaded as shown. Assume L1= 55 in., L2= 40 in., L3 = 25 in., R = 31 kips, Q = 11 kips, and P = 27 kips. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial assembly. R A B R L1 L2 L3 Answers: (a) 81 i in. in. An (9) (c) Omax i ksi
3) will upvote anyone who will answer
QL/ Twe rad have the Same cross- Sectional area; Mad from steel anel Bron ze as shown in fig1. Find the stress in each rood when Est = 200GPa j Eb=83Gpa. br st 3m 30 30 Fig1
Hello can you help me here please?
Solve all the parts ( Hand written please )
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
A hollow, metal circular pipe ABC (see figure) supports a load P, = 113.2 kips acting at the top. P1 A dAB tAB P2 B Саp plate dBC tBC A second load P, = 22 kips is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are daR = 1.75 in., tAR = 0.5 in., dar = 2.45 in., and tac = 0.375 in., respectively. The modulus of elasticity is 28,000 ksi. When both loads are fully applied, the wall thickness of pipe segment BC increases by 200 x 10-6 in. Assume the material behaves linearly elastically. (a) Find the increase in the inner diameter of pipe segment BC (in inches). in. (b) Find Poisson's ratio for the metal. (c) Find the increase in the wall thickness of pipe segment AB (in inches). in. Find the increase in the inner diameter of segment AB (in inches). in.
The following tubular A36 steel shaft has an inner diameter of 25mm and an outer diameter of 35mm under the following loading condition. Determine the angle of twist of the end V. Consider: GA-36 = 75 GPa 1) What would happen if a solid shaft was used? 2) As a designer, do you recommend a solid or tubular shaft for the loading above? Why?
CE 1
Solve for the EI A using conjugate, beam method 3m 50 kN 2m EID @ pt. C 60KN die 2.5m å
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.