A hollow mast of circular section as shown is to be stiffened by bonding two strips of the same material and of rectangular section to the mast throughout its length. Determine the proper dimension h of each near-rectangle which will exactly double the stiffness of the mast to bending in the y-z plane. (Stiffness in the y-z plane is proportional to the area moment of inertia about the x-axis.) Take the inner boundary of each strip to be a straight line. Assume d = 110 mm, D = 225 mm, w = 55 mm. h

A hollow mast of circular section as shown is to be stiffened by bonding two strips of the same material and of rectangular section to the mast throughout its length. Determine the proper dimension h of each near-rectangle which will exactly double the stiffness of the mast to bending in the y-z plane. (Stiffness in the y-z plane is proportional to the area moment of inertia about the x-axis.) Take the inner boundary of each strip to be a straight line. Assume d = 110 mm, D = 225 mm, w = 55 mm. h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the ratio moment of inertia of a rectangular shape to triangular shape having the same base width(b) and height(h) with respect to the baseline would be
It is common to hang objects on doorknobs and over-the-door hooks. There is a limit to the amount of weight that a door can hold because of the forces exerted on the hinges. A door of height h = 2.5 m and width h/2 has a mass of M = 36 kg. The mass is distributed uniformly, so the center of mass is located at the geometric center of the door. One hinge is located a distance h/4 from the top of the door. The second hinge is a distance h/4 from the bottom of the door. Refer to (a) in the figure. The door’s weight is supported entirely by the two hinges and each hinge supports half of the weight. In other words, the vertical force exerted by each hinge is exactly one half of the total weight, including any additional load. For this problem, take the positive y-direction to be directly upward and the positive x-direction pointing from the hinge side of the door to the knob side. 1.) calculate the force, with its sign in Newtons that the upper hinge exerts on the door in the x axis.…
Consider a hollow drainage concrete cylinder of uniform mass density of 2,400kg/m^3 with length L=60m with R1 of 2.8m. Find its outer radius (R2) in m if the moment of inertia is 5, 067, 000kgm^-2 about its axis to symmetry is.
The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. Assume b = 18 in., h = 5 in., r = 3 in, R = 7 in. R h a b Answer: Ia-a i in.4 =
Calculate total moment inertia of a lamina if the density is 7780 kg/m3 using theorem of parallel axis at x-x axis. The measurements are in mm.
Consider a wheel of radius r = 0.28 m, with six spokes (or three rods of length equal to the diameter of the wheel). The total mass of the wheel is 3.0 kg and 55% of the mass is evenly distributed on the circumference while the rest is evenly distributed on the spokes. Calculate the moment of inertia. r
A built-up section fabricated by attaching a C180x15 to a W250x18 shape with 15 mm rivets as shown. Determine the moment of inertia at the centroid of the built-up section. Answer: Centroidal moment of inertia along x-axis= 48.857x106mm4 Need the complete solution, thanks!
Calculate the polar radius of gyration of the area of the angle section about point A. Note that the width of the legs is small compared with the length of each leg. 1.3" 15" 1.3" A 23" Answer: ka = i in.
Consider an L-shaped plate shown in the figure below. Calculate the moment of inertia I (in kg.m2). The mass of the plate is 3 kg, and the width is w = 0.8 m, height h = 0.5 m, and b = 0.2 m. y. W b
Determine the Polar Moment of Inertia and the radius of gyration of the hatched area in the Figure below, with respect to point O P= 17
Find MOI about the x-axis of the area shown in below fig. *Moment of Inertia *
PROBLEM 4: The region is symmetric about the x-axis. Calculate the moment of inertial about the centroidal x and y axes. ANS: I = 10.35 x 106 mm², I = 1.74 × 106 mm² 17 mm y 68 mm 17 mm 18'mm 27 mm --x