A high-speed flash unit for sports photography requires a flash voltage v(0+) = 3V and dv(t) 24V/s dt t=0 The flash unit uses the circuit shown below. Switch 1 has been closed a long time and switch 2 has been open a long time at t=0. Actually, the long time in this case is 3s. Determine the required battery voltage, VB, when C = VB 3Ω + t = 0 Switch 1 Switch 2 12 3Ω t = 0 C Flash + 1/2 H VB voltage

A high-speed flash unit for sports photography requires a flash voltage v(0+) = 3V and dv(t) 24V/s dt t=0 The flash unit uses the circuit shown below. Switch 1 has been closed a long time and switch 2 has been open a long time at t=0. Actually, the long time in this case is 3s. Determine the required battery voltage, VB, when C = VB 3Ω + t = 0 Switch 1 Switch 2 12 3Ω t = 0 C Flash + 1/2 H VB voltage

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Post-lab Questions If the diode D3 is damaged (as short) draw the output voltage waveform in this case. D1 D2 V1 F1 220Vrms n 50HZ T1 0° 220v:40v D3 D4 transformer
Post-lab Questions 1) If the diode D3 is damaged (as open) draw the output voltage waveform in this case. D1 D2 V1 F1 220Vrms n 50HZ T1 0° 220v:40v D3 D4 transformer
For uncontrolled half wave rectifier, R=80ohm, L=0.15H,f=50Hz and Vm=311V.Find the point when the current reaches to zero in radian.
8. Draw the output waveform for the circuit shown below given Vin(pp)=20V. Write the name of the circuit. D1 and D2 are Germanium Diodes. R2 D1 D2 V82 1.8V 2 10k VIN V81 T2.2V
LVDT produces an rms output voltage of 5.0 V for displacement of 3.5 mm. Calculate the sensitivity of LVDT please explain me
What should I do when I get a current like 0.263187845A, should I round into the simplest form, or keep it and convert into mA?
For a single-phase half wave-controlled rectifier with RL load, use the chart below to find the commutation angle ß for the following cases 1) (a=40°, 0=15° then ß= ) 2) (a=80°, 0 =0° then B= ) 3) (α =100°, 0 =45° then = ) 4) (a=120°, 0=75° then ß= 180° Conduction Angle (0) 160° 140° 120° 100 80° 60% 40% 20° 0° p=0 $=15 6=30 + + 20° 40° 60° X6=75 $90 80° 100 120° Delay Angle (0) 140⁰ 160° 180°
ASAP
İL ic io, la IS Vo, Va vs vL vC LOAD SWITCH vD iD G Redraw the circuit when the switch is ON and OFF. II. Draw the wave shape of is(source current), isw (switch current), vsw (switch voltage), i, (inductor current), v, (inductor voltage), ic(capacitor current), vc(capacitor voltage),ip(diode current), vp(diode voltage). I. TAKE APPROPRIATE POLARITY OF THE VOLTAGES. MARK THE POLARITY IN YOUR FIGURE. TAKE APPROPRIATE DIRECTIONS OF THE CURRENTS. MARK THE DIRECTIONS IN YOUR FIGURE.
The waveform displayed on an oscilloscope is as shown in Figure 3. The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 0.5 V/cm. Determine: (i) amplitude of waveform Q (ii) peak to peak value of waveform P P (iii) frequency of waveform P (iv) angular frequency of waveform Q and (v) phase angle difference between P and Q in Degrees. 主 24°C Type here to search
1- The R.M.S. value of a half-wave rectified current is 10A, its value for full-wave rectification would be - amperes (a) 20 (b) 14.14 (c) 20/z (d) 40/z
Determine Vp(rect), Vr(pp), VDC{filter) and the Ripple factor 10:1 D3 110 V rms Output p(pri) p(sec) 60 Hz 2250 D2 D4 1000μF All diodes are IN4001.