A girder supports four concentrated loads of 800lb as shown in the figure. Assume the support at A is pin and B is a roller. Answer che following: 1. Compute the internal shear force, normal force and moment at a point 18ft from point A. Assign this point as point C. (15 points) 2. Determine the shear and moment in the girder as a function of x, where 12ft

A girder supports four concentrated loads of 800lb as shown in the figure. Assume the support at A is pin and B is a roller. Answer che following: 1. Compute the internal shear force, normal force and moment at a point 18ft from point A. Assign this point as point C. (15 points) 2. Determine the shear and moment in the girder as a function of x, where 12ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part C please
NEED HELP ASAP PLEASE A box beam is constructed of four wood boards as shown in the figure part (a). The webs are , and the flanges are , boards (actual dimensions), joined by screws for which the allowable load in shear is per screw.
Solve the problem with complete and neat solution. Draw the figure. 1. Determine the equivalent force-couple system at the pin (point 0) and roller support. Also, compute the x-intercept of the line of action of the system resultant treated as a single force R of the three forces acting on the simple truss at the pin and roller support. 30 20 kN 25 kN 5 m 3 m 6 m 3 m 30 kN
2. (a) Replace the force system acting on the post by a resultant force and (b) couple moment at point O. (c) If the given is only to be replaced by an equivalent force system, what is the magnitude of the resultant force and where is its intersection with the frame located as measured from point A? P = 301 lb 500 lb-ft 30° 50 lb P 301 lb -3 ft- A B 2 ft 4 ft
show complete solution pls
s shown in the sketch, an interior column AB in a steel frame carries a factored axialcompressive load, Pu = 1540 kips. The column is braced at the top and bottom and the mid-height in the perpendicular plane, and sidesway in the plane of the steel frame is allowed. Thecolumns are 12-ft long, and the columns above and below the column AB are the same size asAB. The adjacent girders are W 18×50 and are 32-ft long. Use A992 steel with Fy = 50 ksi,select the lightest W-section for the column AB. Use stiffness reduction factor where applicable.
Please answer second portion or the highlighted part.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Strength of Materials
subj: civil engineering A 50-mm diameter bar is used as a simply supported beam 3 m long. The flexural stress is limited to 50 MPa. If w = 36. •Find Fb(bottom) and Ft(top). (F = Mc/I) •Plot the flexural stress and draw a shear & moment diagram.
DHE TE For the beam shown below, draw shear and bending moment diagrams and determine the x-coordinate of the maximum bending moment. etwag Bro-M Nofe We Efage=1+ chcominx + Ag + A. x = 6.0 in. B. x = 12.0 in. C. x = 18.0 in. D. x = 9.25 in. y 0 6 in M X w = 100 lbf/in A 12 in Ад V = 100x +Ay € Mg = 0= Ay, 12-100-18 B Ay=113627 ду- 1 in 500.X 2 in
Determine the shear value when x = 6m (from the left) for the beam shown Where: P1 = 51kN; P2 = 42 kN; W1 = 11kN/m; W2 = 21kN/m 4m P1 P2 w2 44/2 m² 4 R R₁ 2 m A EU 5 m W1 3 m
Design the positive moment of the beam shown below, determine the number of 20mm diameter bars and the tension steel area, As. Assume the loads given are already factored. b=260mm d=420mm fe=21MPA fy=275MPA As = sq mm. n = 50KN 3m 20 KN/m