A gear drive consists of a 16-tooth 20° steel spur pinion and a 48-tooth cast-iron gear having a pitch of 12 teeth/in. For a power input of 1.35 hp at a pinion speed of 700 rev/min, select a face width based on an allowable contact stress of 100 kpsi. Refer to table number 14-8 for elastic coefficient. The face width based on an allowable contact stress of 100 kpsi is in.

A gear drive consists of a 16-tooth 20° steel spur pinion and a 48-tooth cast-iron gear having a pitch of 12 teeth/in. For a power input of 1.35 hp at a pinion speed of 700 rev/min, select a face width based on an allowable contact stress of 100 kpsi. Refer to table number 14-8 for elastic coefficient. The face width based on an allowable contact stress of 100 kpsi is in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
A 20° 20-tooth cast-iron spur pinion having a module of 4 mm drives a 32-tooth cast-iron gear. Find the contact stress if the pinion speed is 1020 rev/min, the face width is 50 mm, and 10 kW of power is transmitted. Refer to table number 14-8 for elastic coefficient. The contact stress is MPa.
A pair of cast iron bevel gears connects the two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm. The shape of the gear teeth is 14½0 composite form. The allowable static stress for both gears is 55 MPa. If the pinion transmits 2.95 kW of power at 1200 rpm, determine the module and the number of teeth in each gear from the power point of view and check the design from the wear point of view. Take the surface resistance limit is 630 MPa and the modulus of elasticity for cast iron is 84 kN/mm2.
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720 rev/min drives a 28-tooth 240 Bhn steel gear having a 2.5 -in face and a diametral pitch of 5 teeth/in. Find the factor of safety of this drive based on bending strength if 17.5 hp is transmitted. Use Ko=Ks=1, Km=1.6 and Qv=7.
A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=0.154 – 0.912/T, where T represents the equivalent num- ber of teeth. The velocity factor is given by C, = 6 + v where v is the peripheral speed of the gear in m/s.
= Q.3: Calculate the power that can be transmitted safely by a pair of spur gears with the data given below and calculate also, the bending stresses induced in the two wheels when the pair transmits this power. Number of teeth in the pinion 20, Number of teeth in the gear = 80, Module = 4 mm, and Width of teeth = 60 mm, Tooth profile involute, Allowable bending strength of the material;( 200 MPa, for = 400 r.p.m and pinion) and (160 MPa, for gear), Speed of the pinion Service factor = 0.8. = 20° Q.4: Design a wire rope for an elevator (Miscellaneous hoists) in a building of (60 m) height, for a total load (20 kN). The speed of the elevator is (240 m/min) and the full speed is reached at (10 sec). Taken the grade wire is (110), the safety factor is 2.5 and Er =84 x 103 N/mm².
A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=0.154– 0.912/T; , where Tg represents the equivalent num- ber of teeth. The velocity factor is given by C, where 6 + v v is the peripheral speed of the gear in m/s.
In the double-reduction gear train shown (dimensions are in inches), shaft a is driven by a motor attached by a flexible coupling attached to the overhang. The motor provides a torque of 2500 lbf-in at a speed of 1200 rpm. The gears have 20° pressure angles, with diameters shown in the figure. Use an AISI 1020 cold-drawn steel. Design Shaft CD with a design factor of 1.5 by performing the following tasks. (a) Sketch a general shaft layout, including means to locate the gears and bearings, and to transmit the torque. (b) Perform a force analysis to find the bearing reaction forces, and generate shear and bending moment diagrams. (c) Determine potential critical locations for stress design. (d) Determine critical diameters of the shaft based on fatigue and static stresses at the critical locations. (e) Make any other dimensional decisions necessary to specify all diameters and axial dimensions. Sketch the shaft to scale, showing all proposed dimensions. (f) If any of the deflections…
A steel spur pinion has 16 teeth cut on the 20° full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 4 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the gears is 4 kN. If the contact fatigue strength of the steel can be estimated from the AGMA formula of Sc= 2.22 HB + 200 MPa, estimate the factor of safety of the drive based on a surface fatigue failure. The factor of safety of the drive is 3.086
Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm diameter solod shaft supported by the bearings is to be made of machined AISI 1045 CD steel. The helical gear is subjected to the axial force F-498 y a radial load F- 750 N and a tangential load of F-1.995 N. Assume the component is g at room temperature of 70F and the material has s0s reliability factor. Hint: Be careful when you calculate the bending moment at the fillet, as all the three forces on the helical gear cause bending moment at the fillet. Calculate resultant bedina moment from all the three forces. Bending moment is completely reversed loading.) 25-mm solid round shaft Fillet Bending K, = 2.0 Torsional k, = 1.5 Axial K,18 F. F, F Pump Helical spur gear -50 mm -250-mm dia FIGURE 1. Identify the critical locations) of stress and show it clearly in a diagram. 2 Identity cleary, all the components of stresses (at the critical point) that will be calcurated (by drawing and clearty…
A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the pinion pitch and the gear is 80 mm and 100 mm. The shape of the gear gear was 14 restriction form. The static voltage allowed for both gear is 55 mpa. If the door transports to 2.95 kw power at the turn of 1200 RPM, identify the module and the number of teeth on each gear from the Angle of power and check the design from the Angle of the tear. Take the surface durability limit is 630 mpa and the modulus elasticity to iron cast is 84 kn /mm2.