A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 0. Find: a) The mean load voltage and current b) The r.m.s. value of load current e) The PIV of the diode d) The efficiency of rectification

A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 0. Find: a) The mean load voltage and current b) The r.m.s. value of load current e) The PIV of the diode d) The efficiency of rectification

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
a. Full-wave Bridge-type Rectifier. Consider the following circuit on the right. a.1 Determine the peak and dc output voltage for the bridge rectifier. a.2 Assuming the practical model, what PIV rating is required for the diodes? The transformer is specified to have a 12 V rms secondary voltage for the standard 120 V across the primary. D3 120 V pisec) RL Dz D 10 k) alll
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
What is the zener diode and what are its advantages? In what region of their characteristic curve are zener diodes operated? At what value of zener current is the zener voltage normally specified? How does the zener impedance affect the voltage across the terminals of the device?
Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a single-phase full-wave rectifier. The resistance for R is 53 Ω and ripple-to-ripple current is 15%.Determine the DC voltage and DC current across the resistor. Hence, determine the power absorbed by the load. Assuming all diodes are ideal.
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to t6.1. t1: D...... & D.......2. t2: D...... & D.......3. t3: D...... & D.......4. t4: D...... & D.......5. t5: D...... & D.......6. t6: D...... & D......
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110V / 11-0-11 V is used with R, = 1 KQ. Assume diode as Germanium. DI a) Find Input Voltage Vin RL D2 b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor.
Q1/Consider the circuit in Figure with a transformer of 10:1 transformation ratio and the diodes are silicon. a) What type of circuit is this? (b) What is the total peak secondary voltage? (c) Find the voltage value across the resistor (d) Sketch the voltage waveform across RL (e) What is the PIV for each diode? D3 D 120 V Pisez) Vpouo D D 10 kn lleee