A full bridge inverter with RLC load having the following values: R=7.5 Ohms, L=12.5 mH, C-22 uF. The switching frequency is 500 Hz and the DC input voltage is 180V. The average current supply (consider up to the fifth harmonics in calculation) would be equal to: Select one: a. None of these b. 3.84A c. 1.64A Ⓒd. 5.74A

A full bridge inverter with RLC load having the following values: R=7.5 Ohms, L=12.5 mH, C-22 uF. The switching frequency is 500 Hz and the DC input voltage is 180V. The average current supply (consider up to the fifth harmonics in calculation) would be equal to: Select one: a. None of these b. 3.84A c. 1.64A Ⓒd. 5.74A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

With a single phase full bridge square wave inverter connected to a 24V DC power supply, 50H output frequency AC output is aimed. The load resistance is 10 ohms and the inductor is 250mH. Calculate the maximum value (in milliamps) of the load current. a) 546 b) 474 c) -546 d) -474 e) 323
The load voltage waveform of a single phase full bridge inverter supplied from 30OV DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load vahues are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition c. Find the RMS values of the load voltage and the load current d Calculate and draw the voltage across the load inductance e. Calculate and draw the source current and find its average vahue
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition
A single phase bridge inverter has an RLC load with R-20 ohm, L32 mit and C-0115 m The inverter frequency is to 60 H and DC input voltage is Vs 110V The average current of each transistor is equal to fontider up to the fifth harmonics in calculation Select on O None of these b 18A Oc 223A Od 6.JA
A single-phase bridge inverter is fed from 230 V dc. In output voltage wave, only fundamental voltage component is considered. Determine the rms current ratings of an SCR and a diode of the bridge for the following types of loads (i) R= 2 ohm (ii) ωL= 2 ohm. Find also the repetitive peak voltage that may appear across a thyristor in part (i) & (ii).
A single phase half-bridge voltage source inverter (VSI) has a resistive load of 2.4Ω andinput dc voltage Vdc = 48V. The desired fundamental frequency of the load voltage is 50 Hz.Determine: RMS output voltage at fundamental frequency and voltage rating of switches
2) A single-phase full-bridge inverter has a DC voltage source V = 230 V. The rms value of the fundamental component of the output voltage is a- 90 V. b- 207 V. C- 350 V. d- 196 V.
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 2N and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .014 ,02 .01 Time (sec) .012 .016 .018 a. Find the RMS values of the load voltage and the load current b. Calculate and draw the voltage across the load inductance c. Calculate and draw the source current and find its average value
A full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vdc=100 V, R equals to 10 Ohm, and L equals 25 mH. The average current in the dc source is. Select one: O a. 52 A O b. None of the above O c. 4.41 A O d. 300 A
A full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vdc=100 V, R10=Ohm, and L= 25 mH. The power absorbed by the load is. Select one: O a. None of the above O b. 1500 W O c. 1000 W O d. 441 W
The gate of a JFET is . . biased Select one: a. forward b. reverse as well as forward c. none of the above d. reverse
One half bridge inverter with bidirectional switches and one full bridge inverter with bidirectional switches are connected to similar loads (R=102) and providing both an output power of 1 KW. The rms transistor currents of the half bridge and full bridge inverters are respectively: Select one: O a. 5A, 7.07A O b. 5A, 5A O c. 7.07A, 5A Od. None of these