A force vector applied F= 3 i + 4j applied on amassof block (M) on frictionless horizontal surface abwJulol yööl . the displacement function of motion2X= t + t +1, find the mass of the body ( M)älïS 2ɔ

Given: The force applied (F→) on a block is 3i^+4j^. The displacement (x) function is given as…

A force vector applied F= 3 i + 4 j applied on amass of block (M) on frictionless horizontal surface ahw Julol gööl . the displacement function of motion X= t +t +1, find the mass of the body ( M)älïS 3>

A force vector applied F= 3 i + 4 j applied on amass of block (M) on frictionless horizontal surface ahw Julol gööl . the displacement function of motion X= t +t +1, find the mass of the body ( M)älïS 3>

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

An 5.2 kg wooden block is held against a wall with force (Fx) = 9.8 N. The friction coefficient between the two surfaces (µ)=0.50. Determine the acceleration of the block if a upward force of 36.0 N is applied. Use positive for an upward acceleration and negative for a downward acceleration.
300mm HW Blocks A and B have a mass of 7 kg and 10 kg. respectively. Using the coefficients of static friction indicated, determine the largest vertical force P which can be applied to the cord without causing motion. 400 mm a-04
Enter an expression for the magnitude of the force of the bottom-most parcel on the center parcel valid for any value of the vertical acceleration, ay, using only the parameters provided in the palette
Fig. P3-2 33 A homogeneus cylinder weighing 00 Ib sts against two smooth planes that form a trough as shown in Fip. P3. Determine the forces exerted on the cylinder by the planes at contact points A and 8. Fig. P3
Needs Complete typed solution with 100 % accuracy.
Problem 06: Find the missing load (F) in the figure given the resultant of these three parallel loads is 30KN acting up at 10 meters to the right of A. Compute the magnitude and position of the missing load. ( 40 KN 60 KN 2 mtrs 1l mtrs
One day, you are driving your car down the highway, and you notice that you are driving well over the speed limit. You apply the brakes of the carapplying a variable stopping force, until the car slows down to a rea sonable speed of 22.4 m/s (50 mph)A computer plots the force versus time for the vehicle and then measures the area under the curve. It is found that the area is - 18.950N . The total breaking time was 5.4 s. Given that the combined mass of you and your car 1sm = 1200 kg how fast were you moving before applying the breaks? What is the average force applied by the road to the car during breaking? (Note: 1Ns=1kg* m/s)
250 2. 120 Draw the triangle of for ces and determine the resul tant of the two A shown forces acting in the figure. Point A as on
What is the normal force acting on a 10kg box if it is on a flat frictionless surface being pushed with a horizontal foce of 20N?
Q1 Q1\ ABD consists Isosceles triangle. The AB and AD help support pole AC. Known that the tension in AB is double AD tension and the distance between A and C is 0.7 of BD. Determine the magnitude of these tensions if the value of resultant forces is 120 Ib. B.
To be compliant with regulations the inclination angle of awheelchair ramp must not exceed 4.76°. If the wheelchair rampmust have a vertical height of 1.22 m, what is its minimum horizontal length?
The elastic limit of Alis 1.8 X 10^8 Pa. Find theminimum radius (meter)of an Al wire that couldsupport a 10.0 kg masswithout surpassing itselastic limit