A force of P= 200 N is applied to block A and causes block A to accelerate to the right on a rough surface as shown in Figure below. Knowing that the mass for block A is 10 kg and the mass for block B is 6 kg. The coefficient of kinetic friction between block A and the surface is 0.15. Pulleys are massless and smooth. 30° |(6 +a) kg 6 kg в Determine the tension in the cable attached to block A. Explain with calculations on the possible way(s) to reduce the acceleration of block B.

A force of P= 200 N is applied to block A and causes block A to accelerate to the right on a rough surface as shown in Figure below. Knowing that the mass for block A is 10 kg and the mass for block B is 6 kg. The coefficient of kinetic friction between block A and the surface is 0.15. Pulleys are massless and smooth. 30° |(6 +a) kg 6 kg в Determine the tension in the cable attached to block A. Explain with calculations on the possible way(s) to reduce the acceleration of block B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.79P: The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a)...

See similar textbooks

Similar questions

Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
Q4- Two blocks A and B of weight 350 N and 600 N. respectively are connected by a cord that passes over a frictionless pulley, as shown in the Figure 8. Determine the force P to be applied to block B to produce the impending motion of block B down the plane. Fig. (8) Ma 0.5 50⁰ S H0.4 B 30°
Block A has a weight of 60 lb and block B has a weight of 10 lb. Neglect friction and the mass of the cord and pulleys. The figure shows a system of pulleys and blocks. Block A is located on an inclined surface with a slope of three-fourths. Block B is vertically suspended by a cord that goes over a pulley located at the top end of the inclined surface. The cord then goes downward and to the left, parallel to the slope, then it goes over a pulley fixed to the upper right end of block A. Then the cord goes upward and to the right parallel to the slope. The end of the cord is fixed to the anchor. Determine the speed of block A after it moves 5.7 ft down the plane, starting from rest.
The horizontal position of the 500lb block (B) is adjusted by the 7° wedge (A) under the action of the force "P". The contact surfaces between the block and the wedge are vertical, (neglect the weight of the wedge) If: P=100 lbs / HA = 0.2 / HB = 0.1 Determine the coefficient of friction (Hc) between the 500lb block (B) and the horizontal surface if the entire system is in impending motion. UB 7. B PA
When Crates A and B of mass ma = 38 kg and mB = 74 kg are released from rest, Crate A moves to the right = 0.2 ). The force P = 18 Newtons is always acting on Crate B. The linear spring on a rough surface (u: has a stiffness of k = 480 N and is initially stretched 0.5 meters before the system is released from rest. m Neglect the mass of the pulleys and cables and neglect friction in the pulley bearings. Determine the work done by the external force P (in Joules) when Crate A has moved a distance of 0.5 meters to the right. wwwwm
04-Two blocks A and B of weight 350 N and 600 N, respectively are connected by a cord that passes over a frictionless pulley, as shown in the Figure 8. Determine the force P to be applied to block B to produce the impending motion of block B down the plane. Fig. (8) P=0.5 50° P₂ -0.4 30°
Q3. In the position shown in Figure, the system is in the rest. Cylinder B is considered solid and moves in frictionless bearings. The spring is originally unstretched and has a modulus of 10000 N/m. Assuming that the coefficient of friction is 0.25, what will be the speed V of block A after dropping 20 cm. k=10000 N/m mc= 40 kg A=0.25 20 cm mB= 40 ka לדלק RB= 20 cm mA= 100 kg
Determine the tension in the string and acceleration of the block A and B weighing 1200 N and 400 N connected by a string as shown in figure Assume pulleys are weightless and frictionless. B A 400N 1200N (a)
3. A block of mass m = 2.00 kg rests on the left edge of a block of mass M = 8.00 kg. The coefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00 %3D kg block rests is frictionless. A constant horizontal force of magnitude F = 10.0 N is applied to the 2.00-kg block, setting it in motion as shown in Figure. The distance L that the leading edge of the smaller block travels on the larger block is 3.00 m. L M m M (a) Draw a separate free-body diagram for each block. (b) In what time interval will the smaller block make it to the right side of the 8.00-kg block? as (Note: Both blocks are set into motion when the force is applied.) (c) How far does the 8.00-kg block move in the process?
Two blocks of masses m, = 1 kg and m, = 0.30 kg are connected by a light inextensible cord passing around a fixed frictionless pulley as shown in the figure below. The coefficient of kinetic friction between all surface is given by u = 0.3. The horizontal force, F = 6.00 N, causes to drag block 2 to the left at a constant acceleration. F 2 of 1 (a) Draw the free-body diagram of each block (b) What is the tension on the cord that connects the two blocks? (Ans: 5.02 N) (c) What is the magnitude of the acceleration of the blocks? (Ans: 0.31 m/s)
Block 2 of mass 1.30 kg is stacked on top of another Block 1 of mass 8.60 kg on an incline plane of angle 38° with respect to the horizontal. The two blocks are linked by a rope which passes over a pulley at the top of the incline, as shown in the diagram. The coefficient of kinetic friction between all surfaces is 0.45. (g = 9.8m/s2,cos 38° = 0.788, sin 38° = 0.616) a) Draw the free body diagrams of each block, b) Write Newton's second law components for each block, c) What is the acceleration of each block? d) If the coefficient of static friction between all surfaces is 0.3 find the angle 0 the plane must be inclined for sliding to commence. NOTE: Solutions involving the energy will not be accepted. 38.0
When Crates A and B of mass ma = 40 kg and mB = 72 kg are released from rest, Crate A moves to the right on a rough surface (uk has a stiffness ofk = 430 N and is initially stretched 0.4 meters before the system is released from rest. = 0.4). The force P = 17 Newtons is always acting on Crate B. The linear spring т Neglect the mass of the pulleys and cables and neglect friction in the pulley bearings. Determine the magnitude of the velocity of Crate A (in ") when Crate A has moved a distance of 0.6 meters to the right. Consider g = 10 m 82 * k www P